4. Fault Isolation
_______________
A. Table of the circuit breakers used in this procedure:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
R 105VU ELEC/BAT REF/BCL1 9PB1 F01 R
B. If the test confirms the fault:
(1) If the voltage read on the lower ECAM DU is equal to the voltage read on the voltmeter of the ELEC panel 35VU:
(a) Do the operational test of the BCL (Ref. AMM TASK 24-38-00-710-001).
1 If the test gives the maintenance message CHECK HOT BUS 1
_
POWER CONSUMPTION:
- do the procedure given in (Ref. TASK 24-38-00-810-834).
2 If the test result is TEST OK:
_
- do a check and repair the wiring (Ref. AWM 24-38-01) between: . the pin A/a of the BCL1 (1PB1) and the first terminal block, . the pin A/Y of the BCL1 (1PB1) and the first terminal block.
- do the removal and the restoration of the BAT1 (2PB1) (Ref. AMM TASK 24-38-51-280-001).
(2) If the voltage read on the lower ECAM DU is different from the voltage read on the voltmeter of the ELEC panel 35VU:
- replace the BCL-1 (1PB1) (Ref. AMM TASK 24-38-34-000-001) and (Ref. AMM TASK 24-38-34-400-001).
(a) If the fault continues:
- replace the P/BSW-ELEC/BAT 1 (7PB1).
1 If the fault continues:
_
- do a check of the wiring (Ref. ASM 24-38/01) between: . the pin 2 of the circuit breaker (8PB1) and the pin A/D3 of the ELEC/BAT 1 pushbutton switch (7PB1) . the pin A/D1 of the ELEC/BAT 1 pushbutton switch (7PB1) and the pin A/A of the BCL 1 (1PB1).
a If the wiring is not correct:
_
- repair or replace as necessary.
b If the wiring is correct:
_ - replace the C/B-ELEC/BAT BUS/REF/BCL1 (8PB1).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-38-00∞∞∞∞∞∞∞∞∞∞Page 242
May 01/03 CES C. If the test confirms the fault:
- do a check of the position of the circuit breaker (9PB1).
(1) If the circuit breaker is closed:
- do a check for 28VDC at pin 2 of the circuit breaker (9PB1).
(a) If there is 28VDC:
- do a check and repair the wiring (Ref. ASM 24-38/01) between: . the pin 2 of the circuit breaker (9PB1) and the pin A/C3 of the ELEC/BAT 1 pushbutton switch (7PB1) . the pin A/C1 of the ELEC/BAT 1 pushbutton switch (7PB1) and the pin A/C of the BCL1 (1PB1).
(b) If there is no 28VDC:
- do a check and repair the wiring (Ref. ASM 24-38/01) between: . the pin 1 of the circuit breaker (9PB1) and the 28VDC HOT BUS 703PP.
(2) If the circuit breaker is open:
- close it.
(a) Do a check of the wiring for a short to ground between the pin 2 of the circuit breaker (9PB1) and the pin A/C3 of the ELEC/BAT 1 pushbutton switch (7PB1) (Ref. ASM 24-38/01).
1_ If the wiring is not correct:
- repair it.
2_ If the wiring is correct:
- replace the C/B-ELEC/BAT REF/BCL1 (9PB1).
D. Do the test given in para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-38-00∞∞∞∞∞∞∞∞∞∞Page 243
Nov 01/01R
CES
TASK 24-38-00-810-833
R Loss of the Battery 2 because of an Undervoltage or a Failure of the Voltage R Sensing Circuit
1. Possible Causes
_______________
- BCL-2 (1PB2)
- P/BSW-ELEC/BAT 2 (7PB2)
- wiring
- C/B-ELEC/BAT BUS/REF/BCL2 (8PB2)
- C/B-ELEC/BAT REF/BCL2 (9PB2)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-38-00-810-835 Abnormal Power Consumption on the 28VDC HOT BUS (702PP) AMM 24-38-00-710-001 Operational Test of the Battery Charge Limiter (BCL), (with the CFDS) AMM 24-38-34-000-001 Removal of the Battery Charge Limiter (BCL) (1PB1, 1PB2) AMM 24-38-34-400-001 Installation of the Battery Charge Limiter (BCL)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 电源 3(65)
