A320飞机维护手册 AMM LANDING GEAR 起落架3(36)

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific safety barriers
 No specific warning notice
 No specific access platform 3 m (9 ft. 10 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
32-00-00-481-001  Installation of the Safety Devices on the Landing Gears
 57-55-11-000-006  Removal of the Hinge 1A Extension Fairing

R **ON A/C 001-049, 051-060, 101-101,
 32-12-14-991-005  Fig. 401
 1EFF : ALL 1 32-12-14Page 401 1 1 May 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

R **ON A/C 061-099, 102-149, 151-199, 201-299, 401-499,
 32-12-14-991-005-B Fig. 401A
 **ON A/C 051-060, 301-399,
 Post SB 52-1100 For A/C 051-060,
 32-12-14-991-005-C Fig. 401B
 **ON A/C ALL

 3. Job Set-up
__________
 Subtask 32-12-14-941-050

 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).

 (3)
 On the panel 400VU:

 -make sure that the landing-gear control-lever 6GA is in the DOWN position
 -put a warning notice in position to tell persons not to operate the landing gear.

 (4)
 On the panel 110VU, make sure that the GRAVITY GEAR EXTN handle is folded into the center console.

 Subtask 32-12-14-010-053
 B. Get Access
 (1) Put the access platform in position below the applicable zone 733(743).
 1EFF : ALL 1 32-12-14Page 402 1 1 Aug 01/05 1 1 1CES 1

 4. Procedure
_________
 **ON A/C 001-049, 051-060, 101-101,

 (Ref. Fig. 401/TASK 32-12-14-991-005) R **ON A/C 061-099, 102-149, 151-199, 201-299, 401-499,
 (Ref. Fig. 401A/TASK 32-12-14-991-005-B)
 **ON A/C 051-060, 301-399,
 Post SB 52-1100 For A/C 051-060,

 (Ref. Fig. 401B/TASK 32-12-14-991-005-C)
 **ON A/C 001-049, 051-060, 101-101,

 Subtask 32-12-14-020-050
 A. Removal of the MLG Fixed Fairing Assembly
 WARNING : THE WEIGHT OF THE FIXED FAIRING IS 34kg (75lb).

_______
 NOTE : Do not move the locknuts (2) and (10) or you will cause the fixed

____
 fairing (1) to go out of adjustment.

 (1)
 At the positions C and F, remove the screws (19) and remove the cover plate (20).

 (2)
 Hold the head of the screw (21) and remove the nut (9) and disconnect the bonding strap (8) from the fixed fairing (1).

 (3)
 Remove and discard the cotter pins (4).

 (4)
 Remove the nuts (3) and the washers (5) from the bolts (7).

 (5)
 At the position C:

 (a)
 Remove and discard the cotter pin (13).

 (b)
 Remove the nut (14) and the washer (15).

 (c)
 Remove the bolt (18).

 1EFF : ALL 1 32-12-14Page 403 1 1 Aug 01/05 1 1 1CES 1

 MLG Fixed Fairing Assembly - Location and Detail
 Figure 401/TASK 32-12-14-991-005

R 1EFF : 001-049, 051-060, 101-101, 1 32-12-14Page 404 1 1 May 01/05 1 1 1CES 1

 MLG Fixed Fairing Assembly - Location and Detail
 Figure 401A/TASK 32-12-14-991-005-B

R 1EFF : 061-099, 102-149, 151-199, 201-299, 1 32-12-14Page 405 1401-499, 1Aug 01/05 1 1 1CES 1

 MLG Fixed Fairing Assembly - Location and Detail
 Figure 401B/TASK 32-12-14-991-005-C

R 1EFF : 051-060, 301-399, 1 32-12-14Page 406 1 1 May 01/05 1 1 1CES 1