(f)
Connect the rod ends (34) and (37) to the leg of the nose landing gear.
(g)
Make sure that the bush (39) is in position, install the washers (38), the bolt (40), the washer (28) and the nut (27).
(h)
Install the screw (22), the washer (23) and the nut (24).
(i)
Tighten the nuts (24) and (27) but do not TORQUE and safety them at this time.
(j)
Manually close the forward doors of the nose landing gear so that they touch the forward stops.
1EFF : ALL 1 32-22-00Page 523 1 1 Aug 01/05 1 1 1CES 1
(k)
Make sure that the gap Q is between 0.83 mm (0.0326 in.) and 2.83 mm (0.1114 in.).
(l)
Manually open the forward doors of the nose landing gear.
(m) Do again the adjustment if necessary.
Subtask 32-22-00-820-055
J. Adjust the mismatch at rear of the leg door with the rod end (47). (Ref. Fig. 502/TASK 32-22-00-991-005)
**ON A/C 001-049, 051-061, 101-105, 201-203,
(Ref. Fig. 503/TASK 32-22-00-991-007)
**ON A/C 062-099, 151-199, 204-212,
(Ref. Fig. 503A/TASK 32-22-00-991-007-A) R **ON A/C 106-149, 213-299, 301-399, 401-499,
(Ref. Fig. 503B/TASK 32-22-00-991-007-B)
**ON A/C ALL
(1)
Remove the nut (51) and the bolt (48).
(2)
Disconnect the rod end (47) from the leg door of the nose landing gear.
(3)
Adjust the rod end (47) to get the dimension X = 0 plus or minus 1 mm (0.0393 in.).
NOTE : 1 turn of the rod end (47) causes a 1 mm movement of the door.
____
(4)
Tighten the nut (46) but do not TORQUE and safety it at this time.
(5)
Connect the rod end (47) to the leg door of the nose landing gear.
(6)
Make sure that the bushes (49), (50) and the rod (43) are in position, install the bolt (48) and the nut (51).
1EFF : ALL 1 32-22-00Page 524 1 1 Aug 01/05 1 1 1CES 1
(7)
Tighten the nut (51) but do not TORQUE and safety it at this time.
(8)
Make sure that the dimension X is equal to 0 plus or minus 1 mm (0.0393 in.).
(9) Do again the adjsutment if necessary. R **ON A/C 001-049, 051-061, 101-105, 201-203,
Subtask 32-22-00-820-056
K. Adjust the longitudinal gaps of the leg door. (Ref. Fig. 502/TASK 32-22-00-991-005, 503/TASK 32-22-00-991-007)
(1)
Adjust the gap P to between 7 mm (0.2755 in.) and 9 mm (0.3543 in.) with the rod (43).
(a)
Cut and remove the lockwire and loosen the nuts (41).
(b)
Loosen the lockwashers (42) and turn the rod (43) to adjust the gap P to between 7 mm (0.2755 in.) and 9 mm (0.3543 in.).
(c)
Tighten the nuts (41) but do not TORQUE and safety them at this time.
(2)
Manually close the forward doors of the nose landing gear so that they touch the forward stops.
(3)
Make sure that:
-
the gap T is between 4 mm (0.1574 in.) and 6 mm (0.2362 in.).
-
the gap W is between 7.5 mm (0.2952 in.) and 10.5 mm (0.4133 in.).
(4)
Manually open the forward doors of the nose landing gear.
(5)
Do again the adjustment if necessary.
1EFF : ALL 1 32-22-00Page 525 1 1 May 01/05 1 1 1CES 1R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
Subtask 32-22-00-820-056-A
K. Adjust the longitudinal gaps of the leg door.
(Ref. Fig. 502/TASK 32-22-00-991-005)
**ON A/C 062-099, 151-199, 204-212,
(Ref. Fig. 503A/TASK 32-22-00-991-007-A) R **ON A/C 106-149, 213-299, 301-399, 401-499,
(Ref. Fig. 503B/TASK 32-22-00-991-007-B) R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(1)
Adjust the gap P to between 7 mm (0.2755 in.) and 9 mm (0.3543 in.) with the rod (43).
(a)
Cut and remove the lockwire and loosen the nuts (41).
(b)
Loosen the lockwashers (42) and turn the rod (43) to adjust the gap P to between 7 mm (0.2755 in.) and 9 mm (0.3543 in.).
(c)
Tighten the nuts (41) but do not TORQUE and safety them at this time.
(2)
Manually close the forward doors of the nose landing gear so that they touch the forward stops.
(3)
Make sure that:
-
the gap T is between 4 mm (0.1574 in.) and 6 mm (0.2362 in.).
-
the gap W is between 0 mm (0.0000 in.) and 3 mm (0.1181 in.).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架3(142)
