R 1EFF : 005-049, 051-051, 055-099, 101-105, 1 32-21-27Page 415 1151-199, 201-228, 301-302, 1May 01/05 1 1 1CES 1
R (b) Remove the clamp (101) and the washer (102).
R (c) Disconnect the connector (90) and install the blanking caps.
R (d) Remove the nut (98), the washer (97), the bolt (94), the support
R (96) and the clamp (95).
R (e) Disengage the upper electrical harness of the torque link
R assembly through the hole of the protector (91).
R (2) Disconnect the lower electrical harness from the torque link assembly
R (Ref. Fig. 401/TASK 32-21-27-991-004)
R (a) Remove the nuts (111), the washers (110), the screw (100) and the
R bolt (104).
R (b) Disengage the lower electrical harness and its support (99) from
R the torque link assembly.
R (3) Remove the related fittings from the torque link assembly
R (a) Remove the nut (112), the bolt (93), the washers (92) and (113)
R and the protector (91).
R (b) Remove the nuts (105), the washers (106), the bolts (109) and the
R washers (108). Remove the stop (107).
R (4) Disconnect the center hinge
R (Ref. Fig. 402/TASK 32-21-27-991-001)
R (a) Remove the cotter pin (9) from the nut (8).
R (b) Remove the nut (8), the washer (7) and the screw (10).
R (c) Hold the shaft (1) and remove the nut (6) and the washer (5).
R (d) Remove the shaft (1) with a plastic drift.
R (e) Remove the washers (4), (3) and (2).
R (5) Remove the lower arm
R (Ref. Fig. 403/TASK 32-21-27-991-002)
R (a) Remove and discard the cotter pin (24).
R (b) Remove the nut (25) and the support (23).
R 1EFF : 051-051, 1 32-21-27Page 416 1 1 May 01/05 1 1 1CES 1
R (c) Remove the screw (22) with a soft drift.
R (d) Remove the lower shaft (26) with the EXTRACTOR (J47563).
R (e) Remove the lower arm of the torque links and the washers (20) and
R (21).
R (6) Remove the target support
R (Ref. Fig. 404A/TASK 32-21-27-991-005-A)
R (a) If you have the alternative solution 1
R 1_ Remove and discard the cotter pins (142). Remove the nuts
R (144), the washers (143) and the screws (141).
R 2_ Disconnect the rods (138) from the support (145).
R 3_ Remove and discard the cotter pin (130). Remove the nut (131)
R and the washer (132).
R 4_ Hold the casing (137) in position. Remove the screw (134) and
R the washer (133).
R 5_ Lift the indicator (135) and remove it.
R 6_ Release and remove the screw (139). Remove and discard the
R lockwasher (140).
R 7_ Lift the casing (137) and disengage it from the screw (146).
R Remove the casing (137).
R (b) If you have the alternative solution 2
R 1_ Remove and discard the cotter pins (142). Remove the nuts
R (144), the washers (143) and the screws (141).
R 2_ Disconnect the rods (138) from the support (145).
R 3_ Remove the nut (131) and the washer (132).
R 4_ Hold the casing (137) in position. Remove the screw (134), the
R washer (133) and the spacers (136).
R 5_ Lift the indicator (135) and remove it.
R 6_ Release and remove the screw (139). Remove and discard the
R lockwasher (140).
R 1EFF : 051-051, 1 32-21-27Page 417 1 1 May 01/05 1 1 1CES 1
R 7_ Lift the casing (137) and disengage it from the screw (146).
R Remove the casing (137).
R (7) Remove the upper arm
R (Ref. Fig. 405A/TASK 32-21-27-991-003-A)
R (a) Release and remove the nut (69). Remove the washer (70).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架3(110)
