On the portable data loader:
-
the MDDU READY indication is shown.
-
the power-up test of the FMGC 1 starts.
-at the end of this test, the triple click aural warning sounds.
On the portable data loader:
-the TRANS IN PROG indication is shown
-then, the WAIT RESPONSE indication is shown when the transfer is completed.
On the portable data loader:
-
the MDDU READY indication is shown.
-
the power-up test of the FMGC 2 starts.
-at the end of this test, the triple click aural warning sounds.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R 15. On the portable data loader: On the portable data loader:
R - put the FM BITE DOWNLOAD TOOL - the TRANS IN PROG indication is shown
R (PS4084544-103) into the disk - then, the WAIT RESPONSE indication is
R drive. shown when the transfer is completed.
R 16. On the portable data loader:
R - eject the floppy disk.
R - set the ON/OFF switch to OFF.
R 17. Open the circuit breakers 10CA2
R and 11CA2.
R 18. On the panel 52VU:
R - disconnect the connecting
R cable from the SYST2
R connector.
R - install the FMS LOAD blanking
R plate.
R 19. Close the circuit breakers
R 10CA1, 10CA2, 11CA1, 11CA2 and
R wait 1 minute.
R 5. Close-up________
R Subtask 22-70-00-865-099
R A. Remove the safety clip(s) and the tag(s) and close this(these) circuit
R breaker(s):
R -------------------------------------------------------------------------------
R PANEL DESIGNATION IDENT. LOCATION
R -------------------------------------------------------------------------------
R 121VU COM NAV/ACARS/MU 2RB L06
R Subtask 22-70-00-862-068
R B. De-energize the aircraft electrical circuits
R (Ref. TASK 24-41-00-862-002).
R **ON A/C 001-049, 051-061, 101-105,
TASK 22-70-00-610-008 Upload the FM Data WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______
YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
1. Reason for the Job
__________________
Upload the FM DATA with the Portable Data Loader (PDL) or with a floppy-disk data loader (SUNDSTRAND/ALLIED SIGNAL or equivalent).
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
964-0400-0XX 1 FLIGHT MANAGEMENT SYSTEM LOAD
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 22-70-00-610-009 Crossload the FM Data 24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power
3. Job Set-up
__________ Subtask 22-70-00-861-069
A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(2)
Make sure that the aircraft is in the ground configuration. Subtask 22-70-00-865-109
B.
Make sure that this(these) circuit breaker(s) is(are) closed: -------------------------------------------------------------------------------
PANEL ------ DESIGNATION ------------------------------------------------------- IDENT. LOCATION------------------
49VU AUTO FLT/FMGC/1 10CA1 B02
49VU AUTO FLT/MCDU/1 11CA1 B01
121VU AUTO FLT/FMGC/2 10CA2 M17
121VU AUTO FLT/MCDU/2 11CA2 N20
Subtask 22-70-00-865-110
C. Open, safety and tag this(these) circuit breaker(s):
------PANEL -------------------------------------------------------DESIGNATION ------------------IDENT. LOCATION
-------------------------------------------------------------------------------121VU COM NAV/ACARS/MU 2RB L06 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM AUTO FLIGHT 自动飞行3
