-
The Navigation Data Base with the Active Nav Data Base disk (Page 3: NAV DATA BASE)
-
The AMI file with the applicable disk (Page 4: FM AIRLINE CONFIG (AMI))
-
The OPC file with the FMS Option Configuration Disk (1CAMD1) (Page 5: FM OPTIONS CONFIG (OPC))
-
The Performance Data Base with the FMS Performance Data Base Disk (1CAMD2) (Page 6: PERF DATA BASE).
NOTE : When the FM operational software is loaded, these databases are
____
erased:
-
the Navigation Data Base
-
the AMI file
-
the OPC file
-
the Performance Data Base.
You must reload them after the FM operational sofware loading.
NOTE : You can do the crossloading of all the elements (FM1 TO FM2 on
____ MCDU1 or FM2 TO FM1 on MCDU2), on the related P/N STATUS page (Ref. TASK 22-70-00-610-009).
(1) Do the check of the reference of the elements
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU:
-Adjust the display brightness
with the BRT control
-Push the DATA mode key.
2. On the MCDU: On the MCDU:
-Push the line key adjacent to - The A/C STATUS page comes into view. the A/C STATUS indication.
3. On the A/C STATUS page: On the MCDU:
-Push the line key adjacent to - The P/N STATUS page comes into view. the SOFTWARE STATUS/XLOAD indication.
4. Before you do the uploading procedure, on the P/N STATUS page:
-Read the P/N reference of the
element that you can load
-Make sure that this P/N
reference is not the same as
the P/N reference on the disk.
Otherwise the uploading is not
necessary.
R **ON A/C 106-149, 151-199, 201-299, 301-399, 401-499,
4. Procedure
_________
**ON A/C 201-203,
Subtask 22-70-00-970-068
A. Uploading of the FMGC NOTE : This procedure is for FMGC1. For the FMGC2, which is identical,
____
use the indications between the parentheses.
NOTE : After the loading of one of the FMGCs, you can use the CROSSLOAD
____ function (Ref. TASK 22-70-00-610-009) to directly put the data into the other FMGC.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU1(2):
-Turn the BRT knob to adjust the brightness.
2. On the overhead panel, on the Data Loading Selector:
-set the ON/OFF switch to ON.
3. On the overhead panel, on the Data Loading Selector:
-
push the PREV or NEXT key until you get the indication of the FMGC that you can load,
-
push the SEL CTL key.
On the display of the Data LoadingSelector:
-DB/N: PUSH NEXT/PREV indication is shown.
On the multipurpose disk drive unit:
-the < < MDDU READY > > indication is shown.
On the display of the Data LoadingSelector:
-FMGC1(2)NOT SELECTEDindication is shown,
-FMGC1(2) SELECTED indication is shown.
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
4.
Open the circuit breakers 10CA1 and 10CA2.
5.
Put the navigation data base disk into the disk drive of the MDDU.
6.
Close the circuit breaker 10CA1(2).
7.
On the overhead panel, on the Data Loading Selector:
-push the SEL CTL key.
8.
Eject the disk from the disk drive.
9.
On the Data Loading Selector:
-set the ON/OFF switch to OFF.
10. Open the circuit breaker 10CA1(2) for more than 5 seconds.
On the multipurpose disk drive unit:
-the READY indication is shown,
-then, the WAIT RESPONSE indication is shown.
On the multipurpose disk drive unit:
-the TRANS IN PROG indication is shown after the FMGC safety test,
-When all the data are put into the computer (a time duration of 25 minutes can be necessary), the TRANSF COMPLETE indication is shown.
NOTE : If DISK ERROR is shown at the
____ beginning of the loading, eject and put again the disk into the MDDU. Do not do steps 4, 5 and 6 again. If READY and WAIT RESPONSE indications are shown at the end of the loading, eject the disk. Do step 7 and do not do step 8.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM AUTO FLIGHT 自动飞行3(4)
