(6)
Clean the drain plug (70). Apply a thin layer of engine oil (Material No. CP2442) to a new O-ring (80) , and install the O-ring on the drain plug.
(7)
Install the drain plug (70). TORQUE the plug to between 65 and 85 lbf.in (0.73 and 0.96 m.daN).
(8)
Safety the drain plug (70) to the starter housing with lockwire 0.032 in. (0.8 mm) dia. (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia. (Material No. CP8002)
(9)
Clean the knurled magnetic plug (50). Apply a thin layer of engine oil (Material No. CP2442) on the two new O-rings and install the two O-rings on the knurled magnetic plug.
(10) Install the knurled magnetic plug (50):
(a) Push inward and turn clockwise to engage locking device. R **ON A/C 051-061, 102-105, 201-203,
Subtask 12-13-80-680-051
A. Drain the starter
(1)
Remove the filler plug (10). Discard the O-ring (20).
(2)
Cut and remove the lockwire. Remove the magnetic plug (50).
(3)
Put a container below the starter. Remove the drain plug (70), and let the oil drain in the container 2l (0.5 USgal) . Discard the O-ring (80).
(4)
Measure the quantity of the drained oil:
(a)
If the oil quantity is more than 0.5 l (0.1320 USgal), the starter is serviceable.
(b)
If the quantity is less than 0.5 l (0.1320 USgal), replace the stater (Ref. TASK 80-11-10-000-002) (Ref. TASK 80-11-10-400-002).
(5)
Carefully examine the oil removed from the starter and the magnetic plug (50) for metal particles (Ref. TASK 80-11-10-210-001). Then, remove and discard the O-ring (60).
NOTE : Fine metal particles show normal wear. Large pieces of metal
____
show internal damage.
(6)
Clean the drain plug (70). Apply a thin layer of engine oil (Material No. CP2442) to a new O-ring (80) , and install the O-ring on the drain plug.
(7)
Install the drain plug (70). TORQUE the plug to between 65 and 85 lbf.in (0.73 and 0.96 m.daN).
(8)
Clean the magnetic plug (50). Apply a thin layer of engine oil (Material No. CP2442) to the new O-ring (60) and install the O-ring on the magnetic plug.
(9)
Install the magnetic plug (50):
CAUTION : USE TWO STANDARD WRENCHES TO REMOVE/INSTALL THE MAGNETIC
_______ PLUG. ONE TO HOLD THE OIL DRAIN PLUG ADAPTER THE OTHER TO LOOSEN/TIGHTEN THE MAGNETIC PLUG. OTHERWISE ACCIDENTAL OIL DRAINING OF THE STARTER COULD OCCUR.
(a)
Install the magnetic plug (50) on the drain plug (70). TORQUE to between 8 and 24 lbf.in (0.09 and 0.27 m.daN).
(b)
Safety the magnetic plug (50) to the drain plug (70) and to the starter housing with lockwire 0.032 in. (0.8 mm) dia. (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia. (Material No. CP8002)
R 1EFF : 051-061, 102-105, 201-203, 1 12-13-80Page 307 1 1 May 01/05 1 1 1CES 1 **ON A/C ALL
Subtask 12-13-80-612-052
B. Fill the starter
(1)
Remove overflow plug (40), push inward and simultaneously turn counter clockwise to disengage locking device. Discard O-ring (30).
(2)
Fill starter housing through filler port until the engine oil (Material No. CP2442) flows from the overflow port.
NOTE : The quantity of oil used will be less than 0.8 l (0.21 USgal)
____
(3)
Clean the filler plug (10) and overflow plug (40). Apply a thin layer of engine oil (Material No. CP2442) on the new O-ring (20) and new O-ring (30) , and install the O-rings on the filler plug and the overflow plug.
(4)
Install the filler plug (10) and overflow plug (40) push inward and simultaneously turn clockwise to engage locking device.
5. Close-up
________ Subtask 12-13-80-410-052
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(3)
Remove the warning notice(s).
1EFF : ALL 1 12-13-80Page 308 1 1 Feb 01/05R 1 1 1CES 1
TASK 12-13-80-610-002
Replenish Oil System
1. Reason for the Job__________________
Refer to the MPD TASK: 801110-C2
2. Job Set-up Information______________________
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM SERVICING 1(89)
