Quick Oil Servicing - IDG
Figure 303/TASK 12-13-24-991-302- 12 (SHEET 1)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 12-13-24Page 324 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
Quick Oil Servicing - IDG
Figure 303/TASK 12-13-24-991-302- 22 (SHEET 2)
NOTE : The AMM 20-34-00 gives a list of approved oil brand-names for IDG
____ servicing.
(1)
Remove the dust cap (4) from the pressure fill valve (2).
(2)
Connect the pressure fill hose (3) of the TANK - ENGINE OIL FILLING UP (DH13PM) to the pressure fill valve (2).
(3)
Slowly pump the filtered OILS (Material No. 03-002) into the IDG to 35 psi (2.4131 bar) maximum.
(4)
Stop this operation when the oil level in the sightglass (1) is at the top of the green band.
NOTE : There is a delay between the oil complement and the oil level
____
change in the sightglass.
NOTE : Look at the oil level sightglass of the IDG:
____
(Ref. Fig. 303/TASK 12-13-24-991-302)
-the oil level must be at or near the line between the yellow band and the green band,
-if the oil level is above this position, do the normal procedure of oil replenishing to adjust the oil level.
Subtask 12-13-24-020-056
C. Removal of the Hoses
(1)
Remove the pressure fill hose (3) of the TANK - ENGINE OIL FILLING UP (DH13PM) from the pressure fill valve (2).
(2)
Install the dust cap (4) on the pressure fill valve (2).
(3)
Remove the overflow drain hose (7) from the overflow drain valve (8).
(4)
Install the dust cap (5) on the overflow drain valve (8).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
5. Close-up
________
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-228, 301-302,
Subtask 12-13-24-410-060
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
(3)
Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
-
FOR 1000EM1
437AL, 438AR
-
FOR 1000EM2
447AL, 448AR
(4) Remove the warning notice(s). R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
Subtask 12-13-24-862-051
B. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
FLIGHT CONTROLS - SERVICING
___________________________
TASK 12-13-27-612-001
Oil Replenishment of the THS Actuator (9CE)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) R
No specific safety barriers
No specific warning notice
No specific access platform 5 m (16 ft. 5 in.)
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) 0U145506 1 CONE - MOUNTING, THS ACTUATOR 0U190363 1 TOOL - OIL FILLING, THS ACTUATOR
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 03-003 USA MIL-PRF-7808
LUBRICATING OIL TURBINE SYNTHETIC BASE
(Ref. 20-31-00)
R Material No. 19-003 USA AMS 3819
R LINT-FREE COTTON CLOTH (Ref. 20-31-00) Material No. 19-010 USA AMS 5687 LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA (Ref. 20-31-00)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM SERVICING 1(66)
