(e)
TORQUE the plug (1) to between 1.4 and 1.6 m.daN (10.32 and 11.79 lbf.ft).
(f)
Safety the plug (1) with MISCELLANEOUS (Material No. 19-010).
5. Close-up
________
Subtask 12-13-27-410-052
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the access door 312AR.
Subtask 12-13-27-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 16CE1, 19CE1, 19CE2, 19CE3.
Subtask 12-13-27-942-051
C. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 12-13-27-612-002
Oil Replenishment of the Flap PCU (6201CM) Gearbox
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
1. Reason for the Job__________________
Refer to the MPD TASK: 275451-01
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific No specific No specific No specific circuit breaker(s) safety clip(s)lint-free clothsafety barrierswarning noticecontainer 1 l (0.2641 USgal)Torque Wrench : range 0.20 to 3.60 m.daN (2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 03-003 USA MIL-PRF-7808 LUBRICATING OIL TURBINE SYNTHETIC BASE (Ref. 20-31-00)
R C. Expendable Parts
R R R -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R 2 packing 27-84-51 01 -250
R D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-00-410-001 Close the Main Gear Doors after Access 12-13-27-991-002 Fig. 302
3. Job Set-up
__________
(Ref. Fig. 302/TASK 12-13-27-991-002) Subtask 12-13-27-941-053
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
On the panel 400VU:
-Make sure that the landing-gear control-lever 6GA is in the DOWN position.
-Put the warning notice in position to tell persons not to operate the landing gear or the landing gear doors.
Subtask 12-13-27-010-054
B. Get Access
(1)
Open the main gear door (RH) (Ref. TASK 32-12-00-010-001).
(2)
Make sure that the GROUND LOCK SLEEVE (460005835) is on the applicable main gear door actuator.
Subtask 12-13-27-864-050
C. Depressurize the Hydraulic Systems
(1) Depressurize the Green and Yellow hydraulic systems (Ref. TASK 29-10-00-864-001) (Ref. TASK 29-10-00-864-002).
Flap Power-Control Unit (6201CM)
Figure 302/TASK 12-13-27-991-002
1EFF : ALL 1 12-13-27 Page 309
1 1 Feb 01/98
1 1
1CES 1
Subtask 12-13-27-865-053
D. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
4. Procedure_________
(Ref. Fig. 302/TASK 12-13-27-991-002)
Subtask 12-13-27-612-051
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM SERVICING 1(68)
