Subtask 12-13-79-210-066
E. Before you install oil tank filler cap, ensure that the O-ring seal is in good condition or does not show evidence of leakage. If not , replace seal (Ref. TASK 79-11-10-300-003).
**ON A/C 001-049, 051-061, 101-105, 151-151, 201-203,
Subtask 12-13-79-410-066
F. Install oil tank filler cap. With handle in vertical position, grip handle, push down on the cap and as the same time turn clockwise to engage the locking device.
NOTE : This procedure is for the Old Oil Tank Filler Cap only.
____
(1) Pull up on oil tank filler cap. If the locking device is properly engaged, the cap cannot be pulled from tank.
(2) Push hinged oil tank cap handle down flat into the locked position. R **ON A/C 062-099, 106-149, 152-199, 204-299, 301-399, 401-499,
Subtask 12-13-79-410-066-A
F. Install oil tank filler cap with handle in vertical position WARNING : IF THE HANDLE POSITION IS OPPOSITE TO THE OIL QUANTITY
_______ TRANSMITTER, THERE IS A RISK OF INJURY TO YOUR FINGERS.
WARNING : IN THIS POSITION, THE HANDLE OF THE FILLER CAP CAN ACCIDENTALLY
_______ MOVE TO ITS VERTICAL (UNLOCKED) POSITION. IF IT DOES THIS, THERE IS A RISK THAT PRESSURIZED HOT OIL WILL FLOW OUT OT THE TANK AND CAUSE INJURY (DANGEROUS BURNS).
CAUTION : MAKE SURE THAT THE OIL-TANK FILLER-CAP IS LOCKED. ITS HANDLE
_______
MUST POINT TO THE OIL QUANTITY TRANSMITTER.
CAUTION : A BAD SUPPLY PRESSURE OF THE OIL LUBRICATION UNIT DURING ENGINE
_______
OPERATION CAN OCCUR.
CAUTION : DO NOT USE FORCE TO MOVE THE HANDLE OF THE FILLER CAP. DAMAGE
_______
CAN OCCUR TO ITS LOCKING DEVICE.
R CAUTION : DO NOT TRY TO PULL THE HANDLE OF THE FILLER CAP OUT OF ITS STOP_______
R LIMITS.
R NOTE : This procedure is for the New Oil Tank Filler Cap only.____
R (1) Turn the handle of the filler cap clockwise 45. against its stop to
R engage the locking device.
R NOTE : If the locking device is correctly engaged, the cap can not be____
R pulled from tank.
R (2) Push hinged oil tank cap handle down flat into the locked position.
R **ON A/C ALL
R 5. Close-up________
R Subtask 12-13-79-410-065
R A. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (2) Close the oil tank access door :
R FOR 1000EM1
R 437BL
R FOR 1000EM2
R 447BL
R (3) Remove the warning notice(s).
R TASK 12-13-79-610-002- 01
R Check oil level and replenish (Pressure Filling)
R 1. Reason for the Job__________________
R Refer to the MPD TASK: 791000-C3
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific plastic transparent overflow hose
R No specific warning notice
R B. Consumable Materials
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. CP2442 *
R engine oil Ref. SB CFM 79-001 (Ref. 70-30-00)
R C. Referenced Information
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 79-00-00-281-002 Check of the Electrical Master Chip Detector for
R Particles
R 12-13-79-991-302 Fig. 304
R 3. Job Set-up__________
R Subtask 12-13-79-941-069
R A. Safety Precautions
R (1) On the center pedestal, on the ENG panel 115VU:
R (a) Put a warning notice to tell persons not to start the engine.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM SERVICING 1(83)
