航空资料40(9)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 Impedance bridge and other differential circuits were explored to maximize the magnetic
flux density and corresponding eddy current strength.
 Successful crack detection was achieved with a dual coil configuration that combines a
pancake excitation inductor with a co-located pickup coil to produce a transducer that
requires very little drive current (75 mA) and operates in the desired 10 kHz range.
 Excellent crack detection was achieved even when inspecting through composite repair
doublers approaching 0.5” thickness.
 More sophisticated & rugged electronics package – including digital signal processing to
filter and detect phase shifts - to further improve probe sensitivity were being developed.
GE Inspection Technologies
37
In-situ Sensors & Durability
 Advantage/disadvantage compared to established NDT techniques is that
future sensors remain permanently attached / embedded in place, required
to withstand many decades of aircraft service life
 mechanical structural stresses and ensure sensor performance & substrate bonding
 hot/cold and wet conditions
 Embedded sensors can integrate well with composite materials -
piezoelectric fibers or fiber-optic sensors can be fabricated with CFRP or
GFRP (mitigating risks of sensor debonding) however two difficulties arise
 if component is replaced due of wear or damage, the embedded sensor is also
 maintaining the sensor is difficult, virtually impossible to repair, and not replaceable
 Once installed, sensors provide a simple means of monitoring even areas
that are difficult or dangerous for inspectors to access such as fuel tanks,
wing spars, engine beams, etc. – areas that are difficult to detect
microscopic cracks or corrosion.
 Detection might be in online (measured continuously in flight) or offline
(data downloaded at next inspection or maintenance) modes.
 In-situ SHM sensors would be capable of spotting defects much faster,
leading to considerably shorter inspection times.
 Still, SHM should not entirely replace conventional NDT inspection practices
 Conventional maintenance checks are rarely limited to the precise area specified in
the maintenance manual - maintenance technicians typically take a careful look at
surrounding area outside the actual inspection range.
38
Signal Analysis & Power Mgt
 Processor capabilities now are not limiting damage detection signal
processing, but weight / power are always concerns.
 Data must be managed in a robust system to ensure value and translated
into useful structural health and usage information. DO-178B provide some
structured development guidelines, which is recognized by FAA & EASA
 Many published works recognize patterns from known damage rather than
identify unknown damage. Parametric recognition systems are beginning to
appear (UK published policy in ’07 to guide development for future military
aircraft).
 Parallel processing appears to be mature for some limited applications such
as maneuver recognition in usage monitoring, but not prevalent in damage
detection.
 Energy harvesting methods have been studied that can power sensors
systems by converting structural stresses (strain energy harvesting) into
electrical power via piezoelectric transducers (Sandia Labs, Kansas State,
etc.)
39
Directions
 Aircraft structural design optimization is the ultimate
benefit of SHM
 Structural maintenance inspections are a significant factor in operator’s
Direct Operating Costs.
 Minimize conventional NDI for periodic interval inspections for
airworthiness and due to unusual events (hard landing, impact, lightning
strike, etc.) since structural health data is available.
 Inspection intervals are calculated conservatively based on fatigue and
corrosion growth models. SHM will allow optimizing these assumptions
with actual aircraft flight data.
 SHM sensors can greatly simplify inspections since affixed permanently,
can be activated quickly and reliably (without operator variability)
 Immediate benefit in faster and less costly inspection
 No difficult or dirty access to critical inspection zones
40
 Some technologies are well ahead of others in terms
of development maturity – reliability, robustness,
durability and data analysis are still key issues.
 Future innovative approaches are being developed in
microelectronics, nanomaterials, MEMS, etc. which
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：航空资料40(9)