3. Job Set-up
__________ Subtask 52-32-11-010-061
A. Aircraft Maintenance Configuration
(1) Open the AFT cargo compartment door (referred to as cargo door) and install the actuator safety locks to get access to the internal vent door (Ref. TASK 52-30-00-860-001).
(2) Put the access platform in position at the cargo door. Subtask 52-32-11-865-067
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/HYD POWER/Y 3803GX N30 122VU DOORS/CARGO 1MJ T12 123VU Y HYD/ELEC/PUMP 3802GX AB06 123VU Y HYD/ELEC/ELEC PUMP/NORM 3801GX AB03
Subtask 52-32-11-010-062
C. Get Access
(1)
Remove the access panel 826AR from the cargo door to get access to the interlock mechanism.
(2)
Remove the lining and insulation to get access to the inner side of the cargo door structure (Ref. TASK 52-31-13-000-001).
(3)
Remove the screws and the washers and disconnect the cover assy from the brackets of the cargo door structure.
1EFF : ALL 1 52-32-11Page 571 1 1 Aug 01/05R 1 1 1CES 1
4. Procedure
_________ **ON A/C 001-049, 053-099, 101-149, 201-299, 301-399,
Subtask 52-32-11-820-061
A. Adjustent of the Skin Offset **ON A/C 001-049, 053-099, 101-105, 201-220,
(Ref. Fig. 509/TASK 52-32-11-991-014) **ON A/C 106-149, 221-299, 301-399,
(Ref. Fig. 509B/TASK 52-32-11-991-014-B) **ON A/C 001-049, 053-099, 101-149, 201-299, 301-399,
(1)
Remove the vent door stop from the opened vent door as follows:
(a)
Release the tab washers (187) from the jam nuts (186).
(b)
Loosen the jam nuts (186) to release the adjustment bolts (185).
(c)
Remove the adjustment bolts (185) with the jam nuts (186) and the tab washers (187) from the hinge arms (188).
(d)
Remove and discard the tab washers (187).
(2)
Close the vent door as follows:
(a)
Press the roller lever of the interlock mechanism outboard to release the blockage of the latching shaft.
(b)
Move the door handle down to the locked position and push it into the recess of the door structure.
(3)
Measure the skin offset "A" between the external contour of the vent door and the AFT cargo door.
NOTE : Make sure that the skin offset "A" which must be out of wind
____ is between 0.5 mm (0.0196 in.) and 1.5 mm (0.0590 in.)
1EFF : ALL 1 52-32-11Page 572 1 1 Aug 01/05R 1 1 1CES 1
Adjustment of the Vent Door
Figure 509/TASK 52-32-11-991-014
R 1EFF : 001-049, 053-099, 101-105, 201-220, 1 52-32-11Page 573 1 1 Aug 01/05 1 1 1CES 1
Adjustment of the Vent Door
Figure 509A/TASK 52-32-11-991-014-C
R 1EFF : 051-052, 1 52-32-11 Page 574
1 1 Aug 01/05
1 1
1CES 1
Adjustment of the Vent Door Figure 509B/TASK 52-32-11-991-014-B
R 1EFF : 106-149, 221-299, 301-399, 1 52-32-11Page 575 1 1 Aug 01/05 1 1 1CES 1
(4)
If the skin offset "A" is not correct, adjust the length of the connection rod (181) as follows:
(a)
Cut and remove the lockwire from the lock devices (182).
(b)
Loosen the jam nuts (183) to release the turnbuckle (184).
(c)
Turn the turnbuckle (184) until the skin offset correctly adjusted.
(d)
Tighten the jam nuts (183) and safety them with MISCELLANEOUS (Material No. 19-010) on the lock devices (182).
(5)
Adjust the clearance between the vent door stop and the stop of the vent door frame as follows:
(a)
Pull the door handle out of the recess until it is in the 65 degree position to open the vent door.
(b)
Install the adjustment bolts (185) with the jam nuts (186) and new tab washers (187) in the hinge arms (188).
NOTE : Make sure that the tab washers (187) are correctly
____
attached on the hinge arms (188).
(c)
Close the vent door again (Refer to Para. A.2).
(d)
Turn the adjustment bolts (185) until the clearance is between
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门5(40)
