(5) Remove the rigging pin (30) from the bellcrank lever (37).
(6) Remove the rigging pin (38) from the bellcrank lever (40). **ON A/C 151-199,
Subtask 52-32-21-420-061-A
B. Installation of the Drift Pin Assembly
(1) Install the drift pin (283) to the edge member bearing (284) as follows:
(a)
If removed, install the bush (288) in the fork end of the drift pin (283).
(b)
Move the drift pin (283) into the edge member bearing (284).
(c)
Put the linkage (281) on the drift pin (283) and attach it with the bolt (282), the washers (287) and (289) and the nut (286).
(d) Tighten the nut (286) and safety it with the new cotter pin (285) Subtask 52-32-21-420-062-A
C. Installation of the Linkage Assembly NOTE : The linkage assembly includes the horizontal connection rods (290)
____ and (296) and the vertical control rods (306), (311) and (317).
(1) If necessary, assemble the bearing housing (305) as follows:
(a) Put the shaft lever (309) in position and move the support shaft
(344) into the bearing housing (305).
NOTE : Make sure that their attachment holes are align.
____
(b)
Install the tapered pin (343), the spacer (342) and the nut (341) and tighten it.
(c)
Assemble the bellcrank lever (300) on support shaft (344). NOTE : Make sure that their attachment holes are align.
____
(d)
Install the tapered pin (345), the spacer (346) and the nut (347) and tighten it.
R 1EFF : 106-149, 151-199, 221-299, 301-399, 1 52-32-21Page A469 1401-499, 1Aug 01/05 1 1 1CES 1
(2) If necessary, assemble the housing assy (359) as follows:
(a) Put the shaft lever (314) in position and move the support shaft
(348) into the housing assy (359).
NOTE : Make sure that their attachment holes are align.
____
(b)
Install the tapered pin (352), the spacer (351) and the nut (350) and tighten it.
(c)
Assemble the shaft lever (327) in position on the support shaft (348).
NOTE : Make sure that their attachment holes are align.
____
(d)
Install the tapered pin (353), the spacer (354) and the nut (355) and tighten it.
(e)
Put the housing assy (359) in position to the beam (349) and attach it with the screws (358) and the washers (357).
(3) If necessary, assemble the double lever assy (380) as follows:
(a) Put the double lever (330) in position and move the support shaft
(382) into the support (381).
NOTE : Make sure that their attachment holes are align.
____
(b) Install the tapered pin (383), the spacer (384) and the nut (385) and tighten it.
(4) Install the horizontal connection rod (290) as follows:
(a) If required, disassemble the connection rod (290) for the
installation as follows:
1 Remove the nuts (295), the washers (294) and the bolts (293).
_
2 Remove the rod-end (281) and (292) from the center rod (291).
_
(b)
Put the rod-ends (281) and (292) and center rod (291) in position to the door structure.
(c)
Assemble the rod-ends (281) and (292) on the center rod (291) and attach them the bolts (293), the washers (294) and the nuts (295).
R 1EFF : 151-199, 1 52-32-21Page A470 1 1 Aug 01/05 1 1 1CES 1
(d)
Install the rigging pin (304) into the bearing assy (305) and the bellcrank lever (300).
(e)
Connect the rod-end (281) to the drift pin (283) as follows:
(f)
Connect the rod-end (292) to the bellcrank lever (300) as follows:
1_ If removed, install the bush (288) into the drift pin (283).
2_ Put the rod-end (281) in position to the drift pin (283) and
attach it with the bolt (282), the washers (287) and (289) and
the nut (286).
3_ Safety the nut (286) with the new cotter pin (285).
1 Put the rod-end (292) in position to the bellcrank (300) and 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM DOORS 舱门5(117)
