(3) Connect the lower ball joint (40) together with the eye end (37) to the lower end of the ball bearing control (52) as follows:
(a)
Install the seal nut (43) on the control cable (52).
(b)
Install the lock nut (42), the new tab washer (41) and the lower ball joint (40) on the control cable (52).
(c)
Tighten the lock nut (42) with your hand. NOTE : Torque and safety the lock nut (42) ) when the drift pin
____
mechanism is correctly adjusted.
(4) Connect the eye end (37) on the lever (33) of the safety shaft as follows:
(a)
If removed, install the bush (34) on the lever (33).
(b)
Put the eye end (37) on the lever (33) and install the bolt (31), the washers (32) and the nut (35).
(c)
Tighten the nut (35) with your hand.
NOTE : Torque and safety the nut (35) when the drift pin
____
mechanism is correctly adjusted.
(5) Connect the upper ball joint (67) together with the eye end (18) to the upper end of the ball bearing control (52) as follows:
(a)
Install the seal nut (62) on the control cable (52).
(b)
Install the lock nut (65), the new tab washer (64) and the upper ball joint (67) on the control cable (52).
(c)
Install the lock nut (68), the new tab washer (69) and the upper ball joint (67) on the control cable (52).
(d)
Tighten the lock nut (68) with your hand. NOTE : Torque and safety the lock nut (68) ) when the drift pin
____
mechanism is correctly adjusted.
R 1EFF : 051-052, 1 52-32-21Page A466 1 1 Aug 01/05 1 1 1CES 1
(6) Connect the eye end (18) to the bellcrank lever (16) as follows:
(a)
If removed, install the bush (17) on the bellcrank lever (16).
(b)
Put the eye end (18) in position on the bellcrank lever (16) and install the bolt (28), the washers (26) and the nut (25).
(c)
Tighten the nut (25) with your hand. NOTE : Torque and safety the nut (18) when the drift pin
____ mechanism is correctly adjusted.
R **ON A/C 106-149, 221-299, 301-399, 401-499,
Subtask 52-32-21-420-061-B
B. Installation of the Drift Pin Assembly
(1) Install the drift pin (8) to the edge member bearing (9) as follows:
(a)
If removed, install the bush (4) in the fork end of the drift pin (8).
(b)
Move the drift pin (8) into the edge member bearing (9).
(c)
Put the linkage (6) on the drift pin (8) and attach it with the bolt (7), the washers (3) and (5) and the nut (2).
(d) Tighten the nut (2) and safety it with the new cotter pin (1). Subtask 52-32-21-420-062-B
C. Installation of the Linkage Assembly NOTE : The linkage assembly includes the horizontal connection rods (28),
____
(29) and (42) and the vertical control rod (35).
(1) Install the horizontal connection rod (42) as follows:
(a)
Install the rigging pin (30) into the bellcrank lever (37).
(b)
Install the rigging pin (38) into the bellcrank lever (40).
(c)
Connect the rod-end (6) to the drift pin (8) as follows: 1 If removed, install the bush (4) into the drift pin (8).
_
R 1EFF : 051-052, 106-149, 221-299, 301-399, 1 52-32-21Page A467 1401-499, 1Aug 01/05 1 1 1CES 1 (d) Connect the connecting rod (42) to the bellcrank lever (41) as follows:
2_ Put the rod-end (6) in position at the drift pin (8) and
attach it with the bolt (7), the washers (3) and (5) and the
nut (2).
3_ Safety the nut (2) with the new cotter pin (1).
1_ Put the connecting rod (42) in position at the bellcrank lever
(41) and attach it with the bolt (24), the washers (25) and
the nut (26).
2_ Safety the nut (26) with the new cotter pin (27).
(2)
Do the same steps again to install the connection rod (28).
(3)
Install the connecting rod (29) as follows:
(a) Put the connecting rod (29) in position and connect it to the bellcrank lever (41) with the bolt (23), the washers (22) and the nut (21).
1 Safety the nut (21) with the new cotter pin (20).
_
(b) Connect the connecting rod (29) to the bellcrank (39) with the bolt (23), the washers (22) and the nut (26).
1 Safety the nut (26) with the new cotter pin (20).
_
(4) Install the vertical control rod (35) as follows:
(a) Connect the upper fork-end of the control rod (35) to the bellcrank lever (40) as follows:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门5(116)
