(104) and the interlock cam (106) of the locking shaft. NOTE : The gap "Z" must be between 1.0 mm (0.0393 in.) and 1.4 mm
____
(0.0551 in.).
(3) Adjust the gap "Z" as follows:
(a)
If necessary, bent the tab washer (103) and remove the stop (105) from the interlock lever (104). (Ref. TASK 52-32-21-000-006).
(b)
Replace the tab washer (103).
(c)
Install the stop (105) on the interlock lever (104) (Ref. TASK 52-32-21-400-006).
(d)
Turn the adjustment screw (101) of the stop (105) in or out until the gap "Z" is correct.
(e)
Tighten the lock nut (102) correctly and safety it with the new tab washer (103).
1EFF : 051-052, 1 52-32-11Page 565 1 1 Aug 01/05R 1 1 1CES 1
Adjustment of the Interlock Mechanism
Figure 508A/TASK 52-32-11-991-013-A
R 1EFF : 051-052, 1 52-32-11 Page 566
1 1 Aug 01/05
1 1
1CES 1
**ON A/C ALL
Subtask 52-32-11-720-050
G. Do the functional test to make sure that the door locking mechanism operates satisfactory (Ref. TASK 52-32-00-720-001).
5. Close-up
________
**ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
Subtask 52-32-11-410-059
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panel 826AR on the cargo door.
(3)
Install the lining and insulation on the cargo door (Ref. TASK 52-32-13-400-001).
R **ON A/C 151-199, 401-499,
Subtask 52-32-11-410-059-A
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panels 826AR, 826BR and 826CR on the cargo door.
(3)
Install the lining and insulation on the cargo door (Ref. TASK 52-32-13-400-001).
R 1EFF : ALL 1 52-32-11Page 567 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
Subtask 52-32-11-865-066
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1MJ, 3801GX, 3802GX, 3803GX
Subtask 52-32-11-410-060
C. Close Access
(1)
Remove the actuator safety locks and close the cargo door (Ref. TASK 52-30-00-860-002).
(2)
Remove the access platform(s).
1EFF : ALL 1 52-32-11Page 568 1 1 Aug 01/05R 1 1 1CES 1
TASK 52-32-11-820-003 Adjustment of the Vent Door
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.5 m (11 ft. 6 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 19-010 USA AMS 5687 LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
tab washers 52-32-22 02A-240
1EFF : ALL 1 52-32-11Page 569 1 1 Aug 01/05R 1 1 1CES 1
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump
52-31-13-000-001 Removal of the Lining and the Insulation
52-32-13-400-001 Installation of the Lining and Insulation
52-32-22-400-001 Installation of the Vent Door
**ON A/C 001-049, 053-099, 101-105, 201-220,
52-32-11-991-014 Fig. 509
**ON A/C 051-052,
52-32-11-991-014-C Fig. 509A
**ON A/C 106-149, 221-299, 301-399,
52-32-11-991-014-B Fig. 509B
**ON A/C 151-199,
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门5(39)
