Adjustment of the Drift Pin Mechanism
Figure 507/TASK 52-32-11-991-016
R 1EFF : 001-049, 053-099, 101-105, 151-199, 1 52-32-11Page 556 1201-220, 1Aug 01/05 1 1 1CES 1 **ON A/C 106-149, 221-299, 301-399,
(Ref. Fig. 507B/TASK 52-32-11-991-016-A) R **ON A/C 401-499,
R (Ref. Fig. 507C/TASK 52-32-11-991-016-C)
R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(1)
Extend the drift pins on the open cargo door as follows:
(a)
Press the roller lever of the interlock mechanism outboard to release the blockage of the latching shaft.
(b)
Move the door handle down to the locked position and push it into the recess of the door structure.
(2)
Install the rigging pin (165) into the bearing assy (164) and the shaft lever (162).
(3)
If you can not install the rigging pin (165) into the shaft lever (162), adjust the length of the control rod (166) as follows:
(a)
If necessary, cut and remove the lockwire from the safety device (169).
(b)
Loosen the upper and lower jam nuts (168).
(c)
Turn the turnbuckle (167) untill you can install the rigging pin
(165) into shaft lever (162).
(d)
Tighten the jam nuts (168) and safety them with MISCELLANEOUS (Material No. 19-010) on the safety devices (169).
(4)
Measure the distance "U" between the end of the extended drift pins
(160) and the edge members of the cargo door.
NOTE : The distance "U" must be between 34.7 mm (1.3661 in.) and 37.7
____
mm (1.4842 in.).
(5) Move the door handle away from the door structure up to the 65 degree position.
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-32-11Page 557 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Adjustment of the Drift Pin Mechanism
Figure 507A/TASK 52-32-11-991-016-B
R 1EFF : 051-052, 1 52-32-11 Page 558
1 1 Aug 01/05
1 1
1CES 1
Adjustment of the Drift Pin Mechanism Figure 507B/TASK 52-32-11-991-016-A
R 1EFF : 106-149, 221-299, 301-399, 1 52-32-11Page 559 1 1 Aug 01/05 1 1 1CES 1
R Adjustment of the Drift Pin Mechanism
R Figure 507C/TASK 52-32-11-991-016-C
R 1EFF : 401-499, 1 52-32-11 Page 560
1 1 Aug 01/05
1 1
1CES 1
(6) Make sure that the ends of the retracted drift pins are behind the skin egdes of the cargo doors.
Subtask 52-32-11-820-060
F. Adjustment of the Interlock Mechanism
(Ref. Fig. 508/TASK 52-32-11-991-013)
(1)
Make sure that the door handle of the opened cargo door is in the fully UNLOCKED position.
(2)
Measure the gap "Z" between the stop assy (173) and the interlock cam
(171) of the latching shaft.
NOTE : The gap "Z" must be between 1.0 mm (0.0393 in.) and 1.4 mm
____
(0.0551 in.).
(3) Adjust the gap "Z" as follows:
(a)
If necessary, bent the tab washer (176) from the lock nut (175).
(b)
Loosen the lock nut (175) remove the stop bolt (174) from the interlock lever (172).
(c)
Replace the tab washer (176) and install it with the stop bolt
(174) and the lock nut (175) on the interlock lever (172).
(d)
Turn the stop bolt (174) in or out until the gap "Z" is correct.
(e)
Tighten the lock nut (175) correctly and safety it with the new tab washer (176).
**ON A/C 051-052,
Subtask 52-32-11-820-059-A
E. Adjustment of the Drift Pin Mechanism
(Ref. Fig. 507A/TASK 52-32-11-991-016-B)
(1) Extend the drift pins (70) on the open cargo door as follows:
(a)
Press the roller lever of the interlock mechanism outboard to release the blockage of the locking shaft.
(b)
Turn the locking handle up to the locked position and push it into the recess of the handle flap.
R 1EFF : ALL 1 52-32-11Page 561 1 1 Aug 01/05 1 1 1CES 1
Adjustment of the Interlock Mechanism
Figure 508/TASK 52-32-11-991-013
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-32-11Page 562 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM DOORS 舱门5(37)
