B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Do the special precaution on the door damper and emergency operation cylinder (Ref. TASK 52-22-00-860-004).
(3)
Close the emergency exit door (Ref. TASK 52-22-00-410-001).
(4)
Remove the access platform(s).
1EFF : 301-399, 1 52-22-12Page 416 1 1 May 01/04 1 1 1CES 1
TASK 52-22-12-000-003 Removal of the Door Buffer
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.20 m (10 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-22-00-010-001 Opening of the Emergency Exit Doors from the Passenger Compartment 52-22-00-860-003 Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder 52-22-12-991-003 Fig. 403
3. Job Set-up
__________ Subtask 52-22-12-865-056
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
1EFF : 301-399, 1 52-22-12Page 417 1 1 May 01/04 1 1 1CES 1 Subtask 52-22-12-010-052
B. Get Access
(1)
Put the access platform into position below the applicable door.
(2)
Partly open the emergency exit door as required (Ref. TASK 52-22-00-010-001).
(3)
Make sure that the special precaution on the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).
4. Procedure
_________ Subtask 52-22-12-020-052
A. Removal of the Door Buffer
(Ref. Fig. 403/TASK 52-22-12-991-003)
(1)
Remove the nuts (44), the washers (43) and the bolts (42).
(2)
Remove the door buffer (41) from the support arm.
1EFF : 301-399, 1 52-22-12Page 418 1 1 May 01/04 1 1 1CES 1
Door Buffer
Figure 403/TASK 52-22-12-991-003
1EFF : 301-399, 1 52-22-12 Page 419
1 1 May 01/04
1 1
1CES 1
TASK 52-22-12-400-003
Installation of the Door Buffer
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 3.20 m (10 ft. 6 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 16-001 ANTI-CORROSION PRIMER (POLYURETHANE ) (Ref. 20-31-00)
Material No. 16-002 GB BAEP 3536 POLYURETHANE TOPCOAT GREY (FOR INTERNAL APPLIC.) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-22-00-010-001 Opening of the Emergency Exit Doors from the Passenger Compartment 52-22-00-410-001 Closing of the Emergency Exit Doors from the Passenger Compartment 52-22-00-860-003 Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder 52-22-00-860-004 Special Precaution after Maintenance on the Door Damper and Emergency Operation Cylinder 52-22-12-991-003 Fig. 403
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门3(97)
