(3)
Make sure that the access platform is in position below the applicable emergency exit door.
4. Procedure
_________ Subtask 52-22-00-860-078
A. Arming of the Door Damper
(Ref. Fig. 204/TASK 52-22-00-991-003)
(1)
Loosen the knurled screw (15) so that the release lever (11) is moveable.
(2)
Move the release lever (11) to its armed position.
(3)
Tighten the knurled screw (15) and safety it with lockwire, MISCELLANEOUS (Material No. 19-010) on the pin of the release lever (11).
(4)
Remove the PIN - RIGGING (1) from the percussion housing (2).
1EFF : 301-399, 1 52-22-00Page 220 1 1 May 01/04 1 1 1CES 1 TASK 52-22-00-860-002
Diaphragm Replacement at the Door Damper and Emergency Operation Cylinder
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.20 m (10 ft. 6 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 02-001 USA MIL-H-5606
OIL, HYDRAULICPETROLEUM FLUID (Ref. 20-31-00) Material No. 19-010 USA AMS 5687
LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
25 shear pin 52-22-14 01 -030 32 diaphragm 52-22-14 01 -050 32 diaphragm 52-22-14 01 -050A 33 seal 52-22-14 01 -080 34 packings 52-22-14 01 -070
1EFF : 301-399, 1 52-22-00Page 221 1 1 May 01/04 1 1 1CES 1
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power
24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power
52-22-00-010-001 Opening of the Emergency Exit Doors from the Passenger Compartment
52-22-00-410-001 Closing of the Emergency Exit Doors from the Passenger Compartment
52-22-00-614-002 Charging of the Door Damper and Emergency Operation Cylinders (1600WM, 1601WM, 1602WM, 1603WM) at the Emergency Exit Doors
52-22-00-991-005 Fig. 205
3. Job Set-up__________
Subtask 52-22-00-861-052
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
Subtask 52-22-00-865-052
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
Subtask 52-22-00-010-060
C. Get Access
(1)
Open the applicable emergency exit door (referred to as door) as required (Ref. TASK 52-22-00-010-001).
(2)
Make sure that the access platform is in position below the applicable door.
1EFF : 301-399, 1 52-22-00Page 222 1 1 May 01/04 1 1 1CES 1 Subtask 52-22-00-860-084
D. Aircraft Maintenance Configuration
(Ref. Fig. 205/TASK 52-22-00-991-005)
(1)
Set the release lever (23) in its swiveled position as follows:
(a)
Remove and discard the lockwire from the knurled screw (22).
(b)
Loosen the knurled screw (22) so that the release lever (23) is moveable.
(c)
Move the release lever (23) rearward so that it comes free from the guide (26).
(d)
Turn the release lever (23) through 90 degrees to get access to the striker assembly (35).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门3(56)
