1EFF : 301-399, 1 52-22-00Page 541 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 542 1 1 May 01/04 1 1 1CES 1
R (c) Tigthen the jam nuts (96) and safety them with the lockwire,
R corrosion resistance steel, dia 0.8 mm (0.30 in.) on the locking
R devices (95).
R Subtask 52-22-00-820-055
R B. Adjustment of the Locking Shaft
R (Ref. Fig. 511/TASK 52-22-00-991-013, 512/TASK 52-22-00-991-014, 513/TASK
52-22-00-991-015)
R (1) Make sure that the inboard handle (77) is correctly adjusted and the
R rigging pin (91) is installed into the intervening lever (92).
R (2) Install the rigging pin (97) into the target lever (98) and make sure
R that it engages in the door structure.
R NOTE : The rigging pin (97) is part of the PIN - RIGGING, DOOR____
R MECHANISM (98D52208282000).
R (3) If you can not install the rigging pin (97), adjust the length of the
R connection rod (107) as follows:
R (a) If required, cut and remove the lockwire and loosen the jam nuts
R (108).
R (b) Turn the rod (110) until you can install the rigging pin (97)
R into the door structure.
R (c) Make sure that the engaging lever (111) touches the fork lever
R (112).
R (d) If not, turn the rod (110) as required.
R (e) Measure the clearance "C" between the adjustment screw (114) of
R the fork lever (112) and the engaging lever (111).
R NOTE : The clearance "C" must be between 1.8 mm (0.0708 in.) and____
R 2.2 mm (0.0866 in.).
R (f) If required, cut and remove the lockwire, loosen the nut (113)
R and turn the adjustment screw (114) to adjust the clearance "C"
R correctly.
R (g) Tigthen the nut (113) and safety it with the lockwire, corrosion
R resistance steel, dia 0.8 mm (0.30 in.) on the fork lever (112).
R Clearances at the Locking Shaft
R Figure 513/TASK 52-22-00-991-015
1EFF : 301-399, 1 52-22-00 Page 543
1 1 May 01/04
1 1
1CES 1
R (h) Tigthen the jam nuts (108) and safety them with the lockwire,
R corrosion resistance steel, dia 0.8 mm (0.30 in.) on the locking
R devices (109).
R (4) Measure the distance "D" between the head of the stop bolt (119) and
R the actuation lever (105).
R NOTE : The distance "D" must be between 0.2 mm (0.0078 in.) and 0.4____
R mm (0.0157 in.).
R (5) If the distance "D" is out of tolerance, adjust the stop bolt (119)
R as follows:
R (a) Remove the nut (122), the washers (120) and (123), the shim
R washer (121) and the stop bolt (119) from the stop fitting (106).
R (b) Prepare the shim washer (121) so that the distance "D" is
R correct.
R (c) Install the stop bolt (119) together with the shim washer (121),
R the washers (120) and (123) and the nut (122).
R (6) Measure the distance "E" between the head of the stop bolt (124) and
R the twin lever (104).
R NOTE : The distance "E" must be between 0.2 mm (0.0078 in.) and 0.4____
R mm (0.0157 in.).
R (7) If the distance "E" is out of tolerance, adjust the stop bolt (124)
R as follows:
R (a) Remove the nut (127), the washers (125) and (128), the shim
R washer (126) and the stop bolt (124) from the stop fitting (118).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门3(72)
