A320飞机维护手册 AMM DOORS 舱门3(71)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

R A. Get Access Opening of the Emergency Exit Doors from the Passenger Compartment Closing of the Emergency Exit Doors from the Passenger Compartment Operational Check of Door Locking /Unlocking and Opening/Closing from Inside and Outside with Door Latching/Unlatching and Functional Check of Hand Force Adjustment of the Emergency Exit Door Adjustment of the Balance Mechanism Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder Special Precaution after Maintenance on the Door Damper and Emergency Operation Cylinder Adjustment of the Proximity Switches (19WV1, 19WV2, 21WV1,21WV2) of the Emergency Exits with the ECAM DU Fig. 511 Fig. 512 Fig. 513 Fig. 514 Fig. 515
R (1) Partly open the applicable emergency exit door (referred to as door) R (Ref. TASK 52-22-00-010-001).
R (2) Make sure that the special precaution procedure for the door damper R and emergency operation cylinder is done (Ref. TASK 52-22-00-860-R 003).
 1EFF : 301-399, 1 52-22-00Page 537 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 538 1 1 May 01/04 1 1 1CES 1

R  Subtask 52-22-00-865-056 
R  B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and 
R  tagged 
R  -------------------------------------------------------------------------------
R  PANEL DESIGNATION IDENT. LOCATION 
R  -------------------------------------------------------------------------------
R  121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 
R  121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 
R  121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05 
R  Subtask 52-22-00-860-069 
R  C. Aircraft Maintenance Configuration 
R  (1) Make sure that the door linings are removed (Ref. TASK 25-23-47-000-
R  012) and (Ref. TASK 25-23-47-000-013). 
R  (2) Add a BALLAST WEIGHT - EMERGENCY EXIT (98D52207557000) on the door to 
R  replace the weight of the door linings during the adjustment 
R  procedure. 
R  (3) Make sure that the door stays in the lifted position. If not, 
R  increase the tension of the torsion spring (Ref. TASK 52-22-00-820-
R  005). 
R  (4) Make sure that the door is adjusted to its correct center position 
R  (Ref. TASK 52-22-00-820-002). 
R  (5) Close the applicable door (Ref. TASK 52-22-00-410-001). 
R  4. Procedure_________ 
R  Subtask 52-22-00-820-053 
R  A. Adjustment of the Inboard Handle 
R  (Ref. Fig. 511/TASK 52-22-00-991-013, 512/TASK 52-22-00-991-014) 
R  (1) Measure the distance "A" between the head of the stop bolt (76) and 
R  the surface of the upper stop fitting (71). 
R  NOTE : The distance "A" must be between 13.3 mm (0.5236 in.) and 13.5____ 
R  mm (0.5314 in.).

 

R  Adjustment of the Inboard Handle 
R  Figure 511/TASK 52-22-00-991-013
 1EFF :  301-399,  1  52-22-00 Page 539 
1  1  May 01/04
 1  1
 1CES  1

 

R  Location of the Rigging Pins 
R  Figure 512/TASK 52-22-00-991-014
 1EFF :  301-399,  1  52-22-00 Page 540 
1  1  May 01/04
 1  1
 1CES  1

 

R  (2) If the distance "A" is out of tolerance, adjust the stop bolt (76) as 
R  follows: 
R  (a) Remove the stop bolt (76), the washers (72) and (73), the spacers 
R  (74) and the shim washer (75). 
R  (b) Prepare the shim washer (75) so that the distance "A" is correct. 
R  (c) Install the stop bolt (76) together with the shim washer (75), 
R  the spacers (74) and the washers (72) and (73). 
R  (3) Measure the distance "B" between the head of the stop bolt (82) and 
R  the surface of the lower stop fitting (83). 
R  NOTE : The distance "B" must be between 13.2 mm (0.5196 in.) and 13.4____ 
R  mm (0.5275 in.). 
R  (4) If the distance "B" is out of tolerance, adjust the stop bolt (82) as 
R  follows: 
R  (a) Move the inboard handle (77) up to get access to the stop bolt 
R  (82). 
R  (b) Remove the stop bolt (82), the washers (78) and (79), the spacers 
R  (80) and the shim washer (81). 
R  (c) Prepare the shim washer (81) so that the distance "B" is correct. 
R  (d) Install the stop bolt (82) together with the shim washer (81), 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门3(71)