• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-26 23:52来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Do the special precaution on the door damper and emergency operation cylinder after maintenance (Ref. TASK 52-22-00-860-004).

 (3)
 Close the door (Ref. TASK 52-22-00-410-001).

 (4)
 Remove the access platform(s).


 1EFF : 301-399, 1 52-22-18Page 204 1 1 May 01/04 1 1 1CES 1


 SEAL - DOOR - REMOVAL/INSTALLATION
__________________________________ TASK 52-22-18-000-001 Removal of the Door Seal
 1.
 Reason for the Job

__________________
 Self Explanatory


 2.
 Job Set-up Information


______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.2 m (10 ft. 6 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-22-00-010-001  Opening of the Emergency Exit Doors from the Passenger Compartment 52-22-00-860-003 Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder 52-22-18-991-001 Fig. 401
 3. Job Set-up
__________ Subtask 52-22-18-865-050
 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
 1EFF : 301-399, 1 52-22-18Page 401 1 1 May 01/04 1 1 1CES 1 Subtask 52-22-18-010-050


 B. Get Access
 (1)
 Open the applicable emergency exit door (referred to as door) as required (Ref. TASK 52-22-00-010-001).

 (2)
 Make sure that the access platform is in position below the partly opened door.

 (3)
 Make sure that the special precaution on the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).


 4. Procedure
_________
 (Ref. Fig. 401/TASK 52-22-18-991-001)
 WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:

_______
 -
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.

 -
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.


 Subtask 52-22-18-020-050
 A. Removal of the Door Seal
 (1)
 Remove the nuts (9).

 (2)
 Remove the screws (10) and the retainers (1), (2), (3), (4) and (5).

 (3)
 Remove the screws (11) and the retainers (6), (7) and (8). NOTE : Identify the screws (10) and (11) for the installation

 (4)
 Remove the door seal (12).


____
 procedure.

 1EFF : 301-399, 1 52-22-18Page 402 1 1 May 01/04 1 1 1CES 1


 Door Seal
 Figure 401/TASK 52-22-18-991-001
 1EFF :  301-399,  1  52-22-18 Page 403 
1  1  May 01/04
 1  1
 1CES  1

 

 TASK 52-22-18-400-001
 Installation of the Door Seal
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific wooden or plastic scraper
 No specific access platform 3.2 m (10 ft. 6 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-011  USA MIL-G-4343 SILICONE GREASE PNEUMATIC SYST AND SEALS (Ref. 20-31-00)
 Material No. 09-016  USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
 Material No. 11-016 USA BOEING BAC 5000 BAC 5504 BAC 5750 CLEANING SOLVENT (Ref. 20-31-00) Material No. 16-001 ANTI-CORROSION PRIMER (POLYURETHANE ) (Ref. 20-31-00)
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM DOORS 舱门3(106)