(3)
Connect the fork link (254) with the drift pin (239) as follows:
(a)
If removed, install the bush (250) to the fork link (254).
(b)
Put the fork link (254) in position to the eye- end of the drift pin (239).
(c)
Install the bolt (249), the washers (248), the spacer (242), the bush (241) and the nut (247) to the fork link (254).
(d)
Tighten the nut (247) and safety it with the new cotter pin (246).
(4)
Connect the fork link (254) with the twin lever (262) as follows:
(a)
If removed, install the bush (263) to the fork link (254).
(b)
Put the fork link (254) in position to the twin lever (262).
(c)
Install the bolt (255), the washers (253), the bush (256), the spacer (257) and the nut (252) to the fork link (254).
(d)
Tighten the nut (252) and safety it with the new cotter pin (251).
1EFF : 301-399, 1 52-22-21Page 461 1 1 May 01/04 1 1 1CES 1 Subtask 52-22-21-420-060
D. Installation of the Intermediate Shaft Assembly
(Ref. Fig. 407/TASK 52-22-21-991-006)
NOTE : Make sure that the punch mark on each lever aligns with the notch
____
of the intermediate shaft during the installation.
(1)
Put the intermediate shaft (325) in position to the door structure.
(2)
Install the flange bearing (346) as follows:
(a)
Put the flange bearing (346) in position to the door structure.
(b)
Make sure that flange bearing (346) engages with the end of the locking shaft (325).
(c)
Attach the flange bearing (346) with the bolts (345) and the nuts
(347) to the door structure.
(3)
Install the support fitting (326) to the door structure as follows:
(a)
Put the support fitting (326) in position to the door structure so that the attachment holes are align.
(b)
Attach the support fitting (326) with the bolts (341) and (343) and the nuts (342) and (348).
(c)
Put the stop fitting (344) in position and attach it with the bolts (341) and (343) and the nuts (342) and (348).
(4)
Turn the intermediate shaft (325) to make sure that it moves easily.
(5)
Put the target lever (322) in the correct position on the intermediate shaft (325) as follows:
(a) Assemble the target lever (322) to the intermediate shaft (325) so that its attachment screw engages in the groove of the shaft.
NOTE : Make sure that the target lever (322) is in the correct
____ position to the related proximity sensor.
(b) Tighten the attachment screw of the target lever (322).
1EFF : 301-399, 1 52-22-21Page 462 1 1 May 01/04 1 1 1CES 1
(6) Connnect the spring unit (275) with the twin lever (262) as follows: WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE SPRING. THE
_______
TENSION IN THE SPRING CAN CAUSE INJURY TO PERSONS.
(a)
If removed, install the bush (276) to the twin lever (262).
(b)
Put the eye-end of the spring unit (275) in position to the fork-end of the twin lever (262).
(c)
Install the bolt (261), the bush (264), the washers (260) and the nut (258) to the twin lever (262).
(d)
Tighten the nut (258) and safety it with the new cotter pin (259).
(7)
Connnect the fork link (254) with the twin lever (262) as follows:
(a)
If removed, install the bush (263) to the fork link (253).
(b)
Put the fork link (254) in position to the twin lever (262).
(c)
Install the bolt (255), the washers (253), the spacer (257), the bush (256) and the nut (252) to the fork link (254).
(d)
Tighten the nut (252) and safety it with the new cotter pin (251).
(8)
Connnect the push rod (290) with the intermediate lever (229) as follows:
(a)
If removed, install the bush (329) to the intermediate lever (229).
(b)
Put the eye-end of the push rod (290) in position to the fork-end of the intermediate lever (229).
(c)
Install the bolt (327), the washers (328), the bush (330) and the nut (332) to the intermediate lever (229).
(d)
Tighten the nut (332) and safety it with the new cotter pin (331).
(9)
Connnect the connection rod (339) with the actuation lever (337) as follows:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门3(128)
