(a)
Remove the nuts (38) and the bolts (41) from the door frame.
(b)
Remove the upper guide fitting (40) and the shim (39) from the door frame.
(6)
Remove the lower guide fittings (48) as follows:
(a)
Remove the nuts (50) and the bolts (47) from the door frame.
(b)
Remove the lower guide fitting (48) and the shim (49) from the door frame.
(7)
Remove the guide fittings (43) as follows:
(a)
Remove the nuts (46) and the bolts (42) from the door frame.
(b)
Remove the guide fitting (43) and the shim (44) from the door frame.
1EFF : 301-399, 1 52-22-31Page 413 1 1 May 01/04 1 1 1CES 1
Stop and Guide Fittings at the Door Frame
Figure 403/TASK 52-22-31-991-002- 12 (SHEET 1)
1EFF : 301-399, 1 52-22-31Page 414 1 1 May 01/04 1 1 1CES 1
Stop and Guide Fittings at the Door Frame
Figure 403/TASK 52-22-31-991-002- 22 (SHEET 2)
1EFF : 301-399, 1 52-22-31Page 415 1 1 May 01/04 1 1 1CES 1 TASK 52-22-31-400-002
Installation of the Stop and Guide Fittings at the Door Frame
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific wooden or plastic scraper
No specific access platform 3.20 m (10 ft. 6 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-013 USA MIL-PRF-81733 TYPE I CLASS A CORROSION INHIBITING BRUSH CONSISTENCY (Ref. 20-31-00)
Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-000-004 Removal of the Door Frame Linings of the LH FWD Emergency Exit Door, zone 231 25-23-47-000-009 Removal of the Door Frame Linings of the RH FWD Emergency Exit Door, zone 232 25-23-47-000-010 Removal of the Door Frame Linings of the LH/RH AFT Emergency Exit Doors, zones 251/252. 25-23-47-400-004 Installation of the Door Frame Linings of the LH FWD Emergency Exit Door, zone 231
1EFF : 301-399, 1 52-22-31Page 416 1 1 May 01/04 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-400-009 Installation of the Door Frame Linings of the RH FWD Emergency Exit Door, zone 232 25-23-47-400-010 Installation of the Door Frame Linings of the LH/RH AFT Emergency Exit Doors, zones 251/252. 52-22-00-010-001 Opening of the Emergency Exit Doors from the Passenger Compartment 52-22-00-410-001 Closing of the Emergency Exit Doors from the Passenger Compartment 52-22-00-860-003 Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder 52-22-00-860-004 Special Precaution after Maintenance on the Door
Damper and Emergency Operation Cylinder 52-22-31-820-001 Adjustment of the Stop and Guide Fittings 52-22-31-991-002 Fig. 403
3. Job Set-up
__________
Subtask 52-22-31-860-051
A. Aircraft Maintenance Configuration
(1)
Make sure that the applicable emergency exit door (referred to as door) is opened as required (Ref. TASK 52-22-00-010-001).
(2)
Make sure that the special precaution on the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).
(3)
Make sure that the access platform is in position below the partly opened door.
(4)
Make sure that the applicable door frame linning is removed as required (Ref. TASK 25-23-47-000-004), (Ref. TASK 25-23-47-000-009) or (Ref. TASK 25-23-47-000-010).
(5)
Make sure that the applicable insulation blankets are removed from the door frame as required.
1EFF : 301-399, 1 52-22-31Page 417 1 1 May 01/04 1 1 1CES 1
4. Procedure
_________ Subtask 52-22-31-910-051
A. Preparation for Installation
(Ref. Fig. 403/TASK 52-22-31-991-002)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM DOORS 舱门3(148)