A320飞机维护手册 AMM DOORS 舱门3(69)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

R  (Ref. Fig. 508/TASK 52-22-00-991-010, 509/TASK 52-22-00-991-011, 510/TASK
 52-22-00-991-012) 
R  (1) Make sure that the door is closed (Ref. TASK 52-22-00-410-001). 
R  (2) Measure the distance "G" between the door edge member and the door 
R  frame. 
R  NOTE : The distance "G" must be between 71.5 mm (2.8149 in.) and 68.5____ 
R  mm (2.6968 in.). 
R  (3) Measure the lateral gaps "E" and the lower gap "F" between the door 
R  and the fuselage from the outboard side. 
R  NOTE : The gaps must be between 2.5 mm (0.0984 in.) and 5.5 mm____ 
R  (0.2165 in.).

 1EFF : 301-399, 1 52-22-00Page 529 1 1 May 01/04 1 1 1CES 1R Lateral and Lower Gaps Fuselage/Emergency Exit Door R Figure 508/TASK 52-22-00-991-010

 1EFF : 301-399, 1 52-22-00Page 530 1 1 May 01/04 1 1 1CES 1

R  Adjustment of Lateral Gaps 
R  Figure 509/TASK 52-22-00-991-011
 1EFF :  301-399,  1  52-22-00 Page 531 
1  1  May 01/04
 1  1
 1CES  1

 

R  Adjustment of Lower Gaps 
R  Figure 510/TASK 52-22-00-991-012
 1EFF :  301-399,  1  52-22-00 Page 532 
1  1  May 01/04
 1  1
 1CES  1

 

R  (4) If the lateral gaps "E" or the distance "G" are out of tolerance, 
R  change the quantity of the adjustment washers (42) as follows: 
R  NOTE : The adjustment washers (42) are installed between the fork-end____ 
R  of the support arm (43) and the control lever (48). 
R  (a) Remove and discard the cotter pin (50) from the nut (49). 
R  (b) Remove the nut (49), the washers (46), the upper hinge bolt (45) 
R  and the bracket (67) from the control lever (48). 
R  (c) Remove the bracket (67), the washer (41), the adjustment washers 
R  (42) and the bushes (47) from the spacer tube (44). 
R  (d) Change the quantity of the adjustment washers (42) as required 
R  until the lateral gaps "E" are correct. 
R  (e) Put the bracket (67), the adjustment washers (42) and the washer 
R  (41) in position and install the bushes (47) into the journal 
R  tube (44). 
R  (f) Install the upper hinge bolt (45), the washers (46) and the nut 
R  (49) on the control lever (48). 
R  (g) Measure the clearance "H" between the adjustment washers (42) and 
R  the spacer tube (44). 
R  NOTE : A clearance of 0.05 mm (0.0019 in.) is permitted.____ 
R  (5) If the lower gap "F" is out of tolerance, change the quantity of the 
R  adjustment washers (63) as follows: 
R  (a) Remove the nut (49), the washers (46) and the upper hinge pin 
R  (45) from the control lever (48). 
R  (b) Remove the journal pin (61) from the upper fork-end of the 
R  support arm (43). 
R  (c) Change the quantity of the adjustment washers (63) as required 
R  until the lower gaps "F" are correct. 
R  (d) Install the journal pin (61) in the upper fork-end (43). 
R  (e) Measure the clearance "J" between the adjustment washers (63) and 
R  the spacer tube (44). 
R  NOTE : A clearance of 0.05 mm (0.0019 in.) is permitted.____

 1EFF : 301-399, 1 52-22-00Page 533 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 534 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 535 1 1 May 01/04 1 1 1CES 1 TASK 52-22-00-820-003

R  (f) Install the upper hinge pin (45), the washers (46) and the nut 
R  (49) to the control lever (48). 
R  (g) Tighten the nut (49) and safety it with the new cotter pin (50). 
R  (6) To set the door in the vertical position, change the quantity of the 
R  adjustment washers (52) as follows: 
R  (a) Remove and discard the cotter pin (60) from the nut (59). 
R  (b) Remove the nut (59), the washers (56) and the lower hinge bolt 
R  (55) from the lifting lever (58). 
R  (c) Remove the bracket (68), the washer (51), the adjustment washers 
R  (52) and the bushes (57) from the spacer tube (54). 
R  (d) Change the quantity of the adjustment washers (52) as required 
R  until the lateral gaps "E" are correct. 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门3(69)