(5)
Close applicable the door (Ref. TASK 52-22-00-410-001).
(6)
Remove the access platform(s).
1EFF : 301-399, 1 52-22-22Page 410 1 1 May 01/04 1 1 1CES 1 TASK 52-22-22-000-002
Removal of the Transmission Shaft
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.2 m (10 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-000-012 Removal of the Door Linings of the LH FWD Emergency Exit Door, zone 231
25-23-47-000-013 Removal of the Door Linings of the RH FWD Emergency Exit Door at zone 251 or RH AFT at zone 252 or LH AFT at zone 232.
52-22-00-010-001 Opening of the Emergency Exit Doors from the Passenger Compartment 52-22-00-860-003 Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder 52-22-22-991-002 Fig. 402
3. Job Set-up
__________
Subtask 52-22-22-010-055
A. Get Access
(1)
Open the applicable emergency exit door (referred to as door) as required (Ref. TASK 52-22-00-010-001).
(2)
Make sure that the access platform is in position below the partly opened door.
1EFF : 301-399, 1 52-22-22Page 411 1 1 May 01/04 1 1 1CES 1
(3) Make sure that the special precaution on the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).
Subtask 52-22-22-865-053
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
Subtask 52-22-22-010-051
C. Get Access
(1)
Remove the door linings from the door as required (Ref. TASK 25-23-47-000-012) or (Ref. TASK 25-23-47-000-013).
(2)
Carefully disengage the VELCRO tapes and remove the insulation mat from the inner side of the door as required.
4. Procedure
_________ Subtask 52-22-22-020-051
A. Removal of the Transmission Shaft
(Ref. Fig. 402/TASK 52-22-22-991-002)
(1) Remove the push rods (1) and (68) from the shaft levers (59) and (61) as follows:
(a)
Remove and discard the cotter pins (65) from the nuts (66).
(b)
Remove the nuts (66), the washers (64), the bushes (70) and the bolts (63) from the shaft levers (59) and (61).
(c)
Remove the eye-ends of the push rods (59) and (61) from the fork-ends of the shaft levers (59) and (61).
(d)
If required, remove the bushes (69) from the shaft levers (59) and (61).
1EFF : 301-399, 1 52-22-22Page 412 1 1 May 01/04 1 1 1CES 1
Transmission Shaft
Figure 402/TASK 52-22-22-991-002
1EFF : 301-399, 1 52-22-22 Page 413
1 1 May 01/04
1 1
1CES 1
(2) Remove the transmission shaft (60) and the shaft levers (59) and (61)
from the structure as follows:
(a)
Remove the nut (67) and the bolt (62) from the shaft lever (61).
(b)
Release the lockwasher (57) and remove the screw (58) from the fork lever (59).
(c)
Cut and remove the cotter pin (50) from the nut (51).
(d)
Remove the nut (51), the washers (52), (53), (54) and (55) from the transmission shaft (60).
(e)
Move the shaft levers (59) and (61) from the splines of the transmission shaft (60).
(f)
Move the transmission shaft (60) until you can disassemble the washers (55) and (56) and the shaft levers (61) and (58).
(g)
Remove the transmission shaft (60) from the structure.
1EFF : 301-399, 1 52-22-22Page 414 1 1 May 01/04 1 1 1CES 1
TASK 52-22-22-400-002 Installation of the Transmission Shaft
1. Reason for the Job
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门3(137)
