NOTE : Apply a thin layer of COMMON GREASE (Material No. 04-001) to the
____
bushes (15) and (24), and the roller (11).
(1) Install the rivet (16), the trunnion (17) and the spring (14) on the lever (18).
1EFF : ALL 1 52-13-31Page 453 1 1 May 01/05 1 1 1CES 1
(2)
Install the pin (36) and the washer (3).
(3)
Safety the pin (36) with a new cotter pin (4).
(4)
Install the bolt (20) and the washer (21) on the bellcrank assy (22).
(5)
Put in position the spring (19).
(6)
Install the bellcrank assy (22) and the bumper (23).
(7)
Put in position the washers (26) and (27) and the spacer (25).
(8)
Install the shouldered bushes (15) and (24) and the lever (18).
(9)
Install the bolt (37) and the washer (38).
(10)
Install the nut (2) and the washer (1). Tighten the nut (2).
(11)
Put in position the roller (11), the washers (9), (10), (12) and (13) and the spacer (8).
(12)
Install the bolt (32) and the washer (33).
(13)
Install the washer (5) and the nut (6). Tighten the nut (6).
(14)
Safety the nut (6) with a new cotter pin (7).
(15)
Install the fitting (30) and the proximity switch (31).
(16)
Remove the blanking caps from the electrical connectors.
(17)
Connect the electrical connector to the proximity switch (31).
(18)
Install the two washers (34) and the two bolts (35).
(19)
Install the two washers (29) and the two nuts (28). Tighten the two nuts (28).
R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 52-13-31Page 454 1201-207, 1May 01/05 1 1 1CES 1R **ON A/C 106-149, 155-199, 208-299, 301-399, 401-499,
Subtask 52-13-31-420-062-A
A. Installation of the Roller and Proximity Switch Mechanism
(Ref. Fig. 412A/TASK 52-13-31-991-019-A)
NOTE : Apply a thin layer of COMMON GREASE (Material No. 04-001) to the
____
bushes (15) and (24), and the roller (11).
(1)
Install the rivet (16), the trunnion (17) and the spring (14).
(2)
Install the pin (36) and the washer (3).
(3)
Safety the pin (36) with a new cotter pin (4).
(4)
Install the bolt (20) and the washer (21) on the bellcrank assy (22).
(5)
Put in position the spring (19).
(6)
Install the bellcranck assy (22) and the bumper (23).
(7)
Put in position the washers (26) and (27) and the spacer (25).
(8)
Install the shouldered bushes (15) and (24) and the lever (18).
(9)
Install the bolt (37) and the washer (38).
(10)
Install the nut (2) and the washer (1). Tighten the nut (2).
(11)
Put in position the roller (11), the washer (13) and the eccentric yoke (8).
(12)
Install the bolt (32) and the bush (33).
(13)
Install the bush (5) and the nut (6). Do not tighten nut (6).
(14)
Install the fitting (30) and the proximity switch (31).
(15)
Remove the blanking caps from the electrical connectors.
(16)
Connect the electrical connector to the proximity switch (31).
(17)
Install the two washers (34) and the two bolts (35).
R 1EFF : 106-149, 155-199, 208-299, 301-399, 1 52-13-31Page 455 1401-499, 1Aug 01/05 1 1 1CES 1
(18) Install the two washers (29) and the two nuts (28). Tighten the two nuts (28).
**ON A/C ALL
Subtask 52-13-31-710-050
B. Adjustment of the Proximity Switch 15WV1 (15WV2)
(1) Adjust the proximity switch 15WV1 (15WV2) of the locking hook of the passenger/crew doors (Ref. TASK 52-71-00-820-001) or (Ref. TASK 52-71-00-820-001).
R **ON A/C 001-049, 051-099, 101-105, 151-154, 201-207,
Subtask 52-13-31-210-053
C. Adjustment of the Upper Hook
(Ref. Fig. 413/TASK 52-13-31-991-016)
(1)
Open the door.
(2)
Put the two shims (thickness 0.2 mm (0.0078 in)) in position in the upper fittings on the door frame.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门3(10)
