(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Put the FAP (6) in position on the holder (7) and install the screws
(4) and the washers (5).
(4)
Adjust the FAP (6) to the middle of the cover-cutting.
(5)
Tighten the screws (4).
(6)
Remove the blanking caps from the electrical connectors.
(7)
Make sure that the electrical connectors are clean and in the correct condition.
(8)
Connect the electrical connectors (3).
(9)
Make sure that the work area is clean and clear of tool(s) and other items.
NOTE : Make sure that the inscription THIS SIDE UP on the CAM and on
____ the OBRM points up when they are installed.
NOTE : Make sure that you push the CAM and the OBRM into the correct
____ slots and not into one of the other slots. All slots have the same dimensions.
(10)
Install the CAM - Cabin Assignment Module (115RH) (Ref. TASK 23-73-19-400-002).
(11)
Install the OBRM - On Board Replaceable Modul (116RH) (Ref. TASK 23-73-21-400-001).
(12)
Close the cover (2) with the quick-release fastener (1).
R 1EFF : 106-149, 301-399, 401-499, 1 23-73-12Page 407 1 1 Config-2 Aug 01/05 1 1 1CES 1 Subtask 23-73-12-865-072
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 18WH, 15WH, 171RH, 157RH, 150RH, 170RH, 14WH, 17WH, 156RH, 151RH.
Subtask 23-73-12-970-056
C. Do the OBRM Download Procedure (Ref. TASK 23-73-00-869-001). Subtask 23-73-12-740-057
D. Do the Interface and Power Up Test of the Cabin Intercommunication Data System (CIDS) (Ref. TASK 23-73-00-740-010).
5. Close-up
________ Subtask 23-73-12-862-057
A. De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
R 1EFF : 106-149, 301-399, 401-499, 1 23-73-12Page 408 1 1 Config-2 Aug 01/05 1 1 1CES 1
R ATTENDANT PANEL - AFT (126RH) - REMOVAL/INSTALLATION____________________________________________________ TASK 23-73-13-000-001 Removal of the AFT Attendant Panel 126RH
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 23-73-13-991-001 Fig. 401
3. Job Set-up
__________
Subtask 23-73-13-861-050
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
1EFF : ALL 1 23-73-13Page 401 1 1 May 01/04 1 1 1CES 1 Subtask 23-73-13-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-399,
49VU COM/CIDS/DEU B/ESS 153RH G03 **ON A/C 301-399,
120VU COM / CIDS / DEU B / NORM FWD 193RH M09 **ON A/C 001-049, 051-099, 101-105, 201-299,
121VU COM NAV/CIDS/DEU B/NORM 162RH M07 R **ON A/C 106-149, 151-199, 401-499,
121VU COM NAV/CIDS/DEU B/NORM 162RH M08 **ON A/C 301-399,
Subtask 23-73-13-865-056
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL SERVICE IDENT. LOCATION -------------------------------------------------------------------------------2001VU CIDS/DEU B NORM/ AFT 194RH C08
1EFF : ALL 1 23-73-13Page 402 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
4. Procedure
_________
(Ref. Fig. 401/TASK 23-73-13-991-001) Subtask 23-73-13-020-050
A. Removal of the aft attendant panel
(1)
Remove the cover (1) from the aft attendant panel (2).
(2)
Remove the screws (3) and the washers (4).
(3) 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM Communications 通讯4(99)
