D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15RA
Subtask 23-72-51-820-051
E. Make sure that the camera(s) are adjusted correctly (Ref. TASK 23-72-51-820-001).
Subtask 23-72-51-710-050
F. Do the operational test of the cameras (Ref. TASK 23-72-00-710-001). **ON A/C 216-216,
5. Close-up
________ **ON A/C 216-216, Post SB 23-1208 For A/C 216-216, Subtask 23-72-51-862-050
A. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
1EFF : 216-216, 1 23-72-51Page 409 1 1 Feb 01/04R 1 1 1CES 1
**ON A/C 216-216,
TASK 23-72-51-820-001
Adjustment of the Cameras
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
R
R A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
23-72-51-000-001 Removal of the Anti-Hijack-System Cameras 23-72-51-400-001 Installation of the Anti-Hijack-System Cameras 24-42-00-861-001 Energize the Ground Service Network from the External
Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power
3. Job Set-up
__________
**ON A/C 216-216,
Post SB 23-1208 For A/C 216-216,
Subtask 23-72-51-861-051
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
Subtask 23-72-51-865-053
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
122VU DOORS/CKPT/VIDEO/SPLY 15RA T16
1EFF : 216-216, 1 23-72-51Page 410 1 1 May 01/05 1 1 1CES 1 1EFF : 216-216, 1 23-72-51Page 411 1 1 May 01/05 1 1 1CES 1 1EFF : 216-216, 1 23-72-51Page 412 1 1 May 01/05 1 1 1CES 1 1EFF : 216-216, 1 23-72-51Page 413 1 1 May 01/05 1 1 1CES 1 **ON A/C 216-216,
**ON A/C 216-216,
4. Procedure_________
**ON A/C 216-216,
Post SB 23-1208 For A/C 216-216,
Subtask 23-72-51-820-050
A. Adjustment of the Cameras
R R R (1) In the cockpit, on the panel 27VU, push the CKPT DOOR VIDEO pushswitch. Make sure that: - The OFF legend in the pushswitch goes off. - The green LED on the related LCD comes on. - The picture for camera 1 shows.
(2) Get a person to stand directly in front of the cockpit door.
(3) Make sure that the bottom of the picture shows the feet of the person standing in front of the cockpit door.
(4) Make sure that the top of the picture shows the head of the person standing in front of the cockpit door,
R R (5) Make sure that the middle of the picture shows the area which is 1 m (3.28 ft.) in front of the cockpit door.
R (6) If the picture for camera 1 is not correct do these steps:
(a) Remove the cover from the camera.
R R (b) Connect the camera adjustment tool to the camera 1, as follows:
R R R 1_ Move the ring on the camera adjustment-tool to the unlockposition.
R R 2_ Put the camera adjustment-tool in position on the camera 1.
R R 3_ Move the ring on the camera adjustment-tool to the lockposition.
(c) Slowly turn the camera 1 clockwise or counterclockwise until the
picture for camera 1 is correct.
R NOTE : You can only turn the camera a maximum of 30 degrees,____
R hard-stops on the camera prevent more movement.
(d) If you cannot adjust the picture correctly replace the camera 1,
(Ref. TASK 23-72-51-000-001) and (Ref. TASK 23-72-51-400-001).
R (e) Disconnect the camera adjustment-tool from the camera 1, as
R follows:
R
R 1 Move the ring on the camera adjustment-tool to the unlock_
R position.
R
R 2 Remove the camera adjustment-tool from the camera 1 housing._
(f) Install the cover on the camera 1.
R (7) In the cockpit, on the panel 119VU, push the pushswitch 16RA one
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM Communications 通讯3(38)
