• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-10-25 12:49来源:蓝天飞行翻译 作者:航空
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

AIAH
Validity : KFC 150 without EFIS _ _ (FM) 22 12 00 Page 6
DEC 99
 
Variante de localisation Alternate location
 
 
14221400AAAAWZ5001 ® 

Autopilot — Identification and location of components
Figure 2
AIAH
Validity : KFC 150 without EFIS 22 12 00
__-_ _ (FM) Page 7
DEC 99
 

  A — "AP DISC TRM INT push—button"
B — "TRIM UP DN" dual inverter
C — "CWS" push—button

14220000AAA0VZ5004 

Autopilot — Identification and location of components
Figure 3
AIAH
Validity : KFC 150 without EFIS 22-12-00 (FM) Page 8
DEC 99
 
®
 
®
14221400AAABWZ5000 

Autopilot — Identification and location of components
Figure 4
 
Variante de localisation Alternate location
 
 
Autopilot — Identification and location of components
Figure 5
AIAH
Validity : KFC 150 without EFIS 22-12-00 (FM) Page 10
DEC 99
 
AUTOPILOT
MAINTENANCE PRACTICES
1. SERVICING
A. Tools and consumable materials
None
B. Routine servicing of "KING" autopilots
Refer to KING Installation Manual P/N 006-0294-00 and KING Service Memo No. 292 at the latest edition.
2. REMOVAL / INSTALLATION - AUTOPILOT
A. Tools and consumable materials
- Two cable clamps T700A2799000008
- Blanking caps and plugs
- Stainless steel lockwire, dia. 0.032 in (0.8 mm) and dia. 0.025 in (0.6 mm)
- Tie wraps
- Tensiometer
- Loctite (TB 08-13C)
- Allen wrench, 3/32 in
B. Removal of B38 pitch trim servo-actuator (Figure 201)
1) Make sure the switch-breaker of the main switch is open.
2) Make sure the autopilot main switch is set to "OFF".
3) Set the elevator tab control to "nose-up" position.
4) Post up a sign prohibiting operation of the elevator tab control.
5) Install the controls immobilization tool on the pilot control wheel.
6) Remove fuselage rear cone 222.
7) Install a cable clamp (2) at the level of rear reel (9).
8) Open baggage compartment door 219 and remove compartment bottom door 242.
9) Install a cable clamp (2) at the level of pulleys (1).
10) Remove screws (16) and pins (15).
11) Remove screw (14) and guard (13) of idler pulley (5).
12) Unlock turnbuckle barrel (7) and threaded ends of cables (6) and (8).
13) Unscrew turnbuckle barrel (7) to disconnect the threaded ends of the cables. Retain the turnbuckle
barrel.
14) Clear the cable from drive capstan (17) and idler pulley (5). NOTE : Protect disconnected cables against damage.
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:TB20 MAINTENANCE MANUAL 22 AUTO FLIGHT TB20飞机维护手册 22 自动飞行(35)