曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
Table 9-16: Normal Voltage Maximum
This test will change the output voltage from 28V or 14V to 30.3V or 15.1V. The test will last for 30
minutes. The ← (backspace) will terminate the test at any time.
VOLT UNDER
egory B equipment. The output voltage will drop to 10
p up at a rate of 0.15 volt/sec for the US standard and at a rate of 0.30 volt/sec for
rd for 30 seconds before it returns to nominal value.
nd sag the voltage to a level and duration specified Table 9-17 with 5 seconds
he test is repeated three times.
This test applies to category Z and 28 volt cat
volts and will ram
EUROCAE standa
VOLT SURGE
This test will surge a
between transients. T
Category Surge Sags
Volt Dwell (msec) Volt Dwell (msec)
RTCA EUR US EUR
A 40 40 30 15 17 30
B 40 40 30 15 17 30
Z 50 50 50 12 12 30
Table 9-17: Voltage Surge
on POWER INTERRUPT.
POWER INTERRUPT
Refer to secti
California Instruments 125
User Manual Compact i/iX Series
9.6.2 Abnormal Test
From
e 9-11.
the DO-160 MENU scroll to the ABNORMAL DC entry using the up and down cursor keys. Press the
ENTER key to select the ABNORMAL screen. The screen will appear as shown in Figur
t has the following tests:
1. VOLT MIN
4. VOLT DROP
5. VOLT SURGE
The above tests can be selected by scrolling to the highlighted selection using the up and down key
and the ENTER key to start the selected test.
VOLT MIN
This test will change the output voltage from 28V or 14V to 20.5V or 10V. The test will last for 30
minutes. The ← key (backspace) will terminate the test at any time.
VOLT MAX
This test will change the output voltage from 28V or 14V to 32.2V or 16V. The test will last for 30
minutes. The ← key (backspace) will terminate the test at any time.
VOLT LOW
This test applies for category B equipment.
This test will change the output voltage to the voltage minimum for one minute. The voltage will decay
linearly to zero voltage in a ten minute period before returning to its nominal voltage.
VOLT DROP
This test will change the output to 12V from 28V or to 6V from 14V for seven seconds. The output
voltage will return to nominal voltage after seven seconds.
Figure 9-11: Abnormal State screens
The Abnormal Tes
2. VOLT MAX
3. VOLT LOW
California Instruments 126
User Manual Compact i/iX Series
VOLT SURGE
This test will produce voltage surge defined by Table 9-18. This test will be repeated three times with
s intervals. The ten second voltage values are halved for 14.0V category B equipment.
Category Surge 1 Surge 2
Volt Dwell (msec) Volt Dwell (msec)
A 46.3 100 37.8 1000
B 60 100 40 1000
Z 80 100 48 1000
Table 9-18: Abnormal Voltage Surge
9.6.3 Emergency Test
The Emergency test is selected from the DO-160 DC Main Menu. This test will set the output voltage
to 18V for 28V equipment and to 9V for 14V equipment. The test will last for 30 minutes. The ← key
(backspace) will terminate the test at any time.
California Instruments 127
User Manual Compact i/iX Series
10. Option -704: MIL-STD 704 Rev D & E (MIL704 Mode)
10.1 General
Option –704 includes a firmware implementation for Mil-Std 704 revision D and E and a short version
of r i MIL704 handbook, the GUI based software
imp e vionics tests are covered by a separate Avionics
Software Manual, CI P/N 4994-971, which is distributed on the same CD as this manual.
This user manual assumes that the user is familiar with the text of the relevant MIL-STD 704, test
standard. No attempt is made to explain or elaborate on the actual test specification. The–704 option
supports both AC and DC power applications.
Test Execution Considerations
Several of the MIL-STD 704 test steps take considerable time to execute. Tests in progress may be
aborted by using the BACK button on the power source front panel.
10.2 Initial
evis on F. For testing to revision F conform the
lem ntation is available. The software based a
Setup
Nominal parameters for the AC Power source are as follows:
5V L-N or 230V L-N
00 Hz for all revisions.
he DC Power source are as follows:
tput Voltage 28V or 270V L-N
Not ble the test and will prevent access to
Output Voltage 11
Output Frequency 360 Hz to 8
60 Hz for revision F only.
Nominal parameters for t
Ou
e: A setting outside these nominal values will disa
the 704 Menu screens or execution of any test step.
The Compa
230VAC no
ct i/iX Series has a maximum voltage range for 300Vrms. Consequently, not all tests for
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
航空资料11(155)
