曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
4.2.1 Power on screens
At initial power up, the i/iX Series power supply will display important configuration information in a
series of power on screens. These displays are only visible for a short period of time and will not reappear
until the next time the unit is turned on.
There are three screens that will appear in the same order:
1. LANetwork detection... At power up, the unit will try to detect a LAN interface. If not found, a “LAN
not available” message will appear. The LAN will not be detected if:
1. No –LAN option is installed.
2. The USB port is connected to a computer.
3. The RS232 port jumper is installed.
This process may take several seconds.
2. Initialization in progress. This means the firmware has started to load.
Company and firmware information. Displays the manufacturer - Cal Inst., 3. which is short for
California Instruments - and the firmware part number and revision. The firmware part number
starts with CIC followed by a three-digit code and dash number. The firmware revision has a major
revision before the decimal point and a minor revision after the decimal point.
4. Model and Serial number information. The model will be a function of the configuration and will
include the series designation (i or iX). The serial number is a 5-digit number. This number should
match the model type sticker located on the back of the unit.
5. Memory test result. If all memory tests pass at power on, the message "MEMORY TEST
PASSED" will appear. If not, an error message will be displayed instead. This information may be
useful when calling in for service support.
California Instruments 53
User Manual Compact i/iX Series
Once the power o
screen shown her
n sequence is completed, the power source will always revert to the PROGRAM
e.
The power source is now ready to be used.
California Instruments 54
User Manual Compact i/iX Series
4.2.2 Top Level Menus
The following op le can be accessed using the Menu ke
RY ION
t - vel menu choices y:
ENT DESCRIPT
PROGRAM AM m output as
changed.
The PROGR enu allows primary parameters such
voltage, frequency, current limit, waveform shape and voltage
range to be
CONTROL The CONTROL menu allows secondary setting parameters such
de, phase as sense mo mode and ALC mode to be changed.
MEASUREMENTS The MEASUREMENT screen is not a menu in that no user entries
are required. It displays read-back data.
TRANSIENTS The TRANSIENTS menu allows output transients to be
programmed.
REGISTERS REGISTERS omp e instrument
settings and transient list programs to be saved to nonvolatile
.
The SETUP menu allows c let
memory
CONFIGURATION
n settings such as the IEEE-488 address, USB or LAN,
tate and Master/Auxiliary control m
The CONFIGURATION menu allows changes to be made to
configuratio
power on s ode.
OUTPUT CAL The OUTPUT CAL menu provides access to the LCD viewing
Calibration password entry. If the c
entered, additional calibration sc
angle and orrect calibration
password is
accessed.
reens can be
MEAS CAL CAL menu allows for calibration o
ent system.
The MEA
measurem
S f the AC source
APPLICATIONS The APPLICATIONS menu provides access to the optional
licatio that may be in
oller.
firmware app n programs stalled in the power
source contr
OPTIONS S menu provides access to opti
ent on the power source.
The OPTION
s
onal functions that
may be pre
ETIME/TEMP
operation) in hours, minutes and
internal temperature of the unit i
The ETIME/TEMP screen displays the Elapsed time (Time the unit
has been in seconds. It also
displays the n degrees Celsius.
LIMITS screen displays the hardware configuration limits of
er sour y purpos the user
none o
The LIMITS
the AC pow
can change
ce. It is for displa
lds.
es only and
f these fie
California Instruments 55
User Manual Compact i/iX Series
4.2.3 Menu Tree
i/iX Series enu Structure
EVEL 1 VEL 1
M
L LEVEL 2 LE LEVEL 2
PROGRAM VOLT 120.0V REGISTERS SAVE REG #
CONTROL FREQ 400.0HZ CONFIGURATION RECALL REG #
VRANGE 150.0V ADDRESS 1
PHASE 0.0° BAUD RATE 460800
FUNC >SINUSOID PON STATE RST
CLIP THD 10.0 CONTROL MAST
VOLT MODE AC LANGUAGE SCPI
DC OFFSET N/A SYSTEM 1501iX
CURR 13.00A (FW 0.25 LANetwork <
OL MODE CV or higher)
SENSE INT -LAN option only IP Address NC
SYNC INT 100.10.1.87
CLOCK INT MAC Address
MODE STAN 0:20:4A:9A:02:FD
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
航空资料11(130)
