曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
a manner not specified by California Instruments, the protection provided by the equipment may be
impaired.
BEFORE APPLYING POWER
1. Verify the correct input voltage is applied to the unit. Allowable input ratings are shown on the model
and serial number tag located at the rear of the unit. The selected input voltage setting is visible on the
voltage selector slide switch on the rear panel of the unit.
2. The chassis and cabinet of this power source must be grounded to minimize shock hazard. A chassis
ground is provided at the input terminal block. This is located on the rear panel of the unit. The
chassis ground must be connected to an electrical ground through an insulated wire of sufficient
gauge.
FUSES
Use only fuses of the specified current, voltage, and protection speed (slow blow, normal blow, fast blow)
rating. Do not short out the fuse holder or use a repaired fuse.
DO NOT OPERATE IN A VOLATILE ATMOSPHERE
Do not operate the power source in the presence of flammable gases or fumes.
DO NOT TOUCH ENERGIZED CIRCUITS
Disconnect the power cable before servicing this equipment. Even with the power cable disconnected, high
voltage can still exist on some circuits. Discharge these voltages before servicing. Only qualified service
personnel may remove covers, replace components or make adjustments.
DO NOT SERVICE ALONE
Do not remove covers, replace components, or make adjustments unless another person, who can
administer first aid, is present.
DO NOT EXCEED INPUT RATINGS
Do not exceed the rated input voltage or frequency. Additional hazards may be introduced because of
component failure or improper operation.
DO NOT MODIFY INSTRUMENT OR SUBSTITUTE PARTS
Do not modify this instrument or substitute any parts. Additional hazards may be introduced because of
component failure or improper operation.
MOVING THE POWER SOURCE
When moving the power source, observe the following:
1. Remove all AC power to unit.
2. Do not carry unit using front panel handles. Handles are intended for pulling power source out of cabinet
only. Support unit at bottom when moving.
3. Do not lift alone. Two man lift recommended.
ALLOW CAPACITORS TO DISCHARGE
Capacitors in the power source may hold a hazardous electrical charge even if the power source has been
disconnected from the mains supply. Allow capacitors to discharge to a safe voltage before servicing internal
circuits or touching exposed pins of the mains supply connectors.
California Instruments 3
User Manual Compact i/iX Series
California Instruments 4
User Manual Compact i/iX Series
WARRANTY INFORMATION
CALIFORNIA INSTRUMENTS CORPORATION warrants each instrument manufactured by them to be free from
defects in material and workmanship for a period of one year from the date of shipment to the original purchaser.
Excepted from this warranty are fuses and batteries that carry the warranty of their original manufacturer where
applicable. CALIFORNIA INSTRUMENTS will service, replace, or adjust any defective part or parts, free of
charge, when the instrument is returned freight prepaid, and when examination reveals that the fault has not
occurred because of misuse, abnormal conditions of operation, user modification, or attempted user repair.
Equipment repaired beyond the effective date of warranty or when abnormal usage has occurred will be charged
at applicable rates. CALIFORNIA INSTRUMENTS will submit an estimate for such charges before commencing
repair, if so requested.
VOIDED WARRANTY
Any misuse or abuse of, as well as any modifications or changes made to any California Instruments product will
automatically void the factory warranty. Removing non-normal use related covers or any sealed covers or lids
also automatically voids factory warranty unless express written or email authorization is obtained from the
customer service department in advance. The customer service department can be reached via email at
support@calinst.com.
SERVICE PROCEDURE
If a fault develops, notify CALIFORNIA INSTRUMENTS at support@calinst.com or its local representative, giving
full details of the difficulty, including the model number and serial number. On receipt of this information, service
information or a Return Material Authorization (RMA) number will be given. Add the RMA number furnished to the
shipping label. Pack the instrument carefully to prevent transportation damage, affix label to shipping container,
and ship freight prepaid to the factory. CALIFORNIA INSTRUMENTS shall not be responsible for repair of
damage due to improper handling or packing. Instruments returned without RMA No. or freight collect may be
refused at California Instruments discretion. Instruments repaired under Warranty will be returned either via
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
航空资料11(109)
