曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
003 page 3004) next page. Make adjustments one link at a time. Optimal tension does
not allow blind mod. to fall freely. Run shade up and down to assure it operates
smoothly.
F. When desired tension is achieved, complete steps C & D in reverse order to complete
adjustment.
G. Re-install window unit. See (“UNINSTALLING WINDOW SHADE UNIT”, section
6 & 7 pages 3002 & 3003). Complete these steps in reverse order.
PAGE 1003
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
FIGURE 3, GRAPHIC 25-23-08-991-003
Showing tension adjustment
PAGE 1004
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
PAGE INTENTIONALLY LEFT BLANK
PAGE 1005
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
UNINSTALLING WINDOW SHADE ASSY.
TASK 25-23-08-000-801
1. General
A. The overhaul instructions contained in this manual are usually implemented in
mechanical overhaul workshops.
B. Avoid removing identification plates, unless manufacturer authorization.
C. Assure window unit inner and outer lens, and any decorative plated parts are protected at
all times when removed from the aircraft.
D. When removing and transporting the window unit assure the shade is in the up position.
TASK 25-23-08-940-801
2. Job set-up information
A. Tools, Fixtures, equipment and materials
None.
TASK 25-23-08-000-802
3. Preliminary Steps
A. Before the uninstalling, make note of the window assy. location for efficient reinstallation
and to prevent errors.
PAGE 3001
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
TASK 25-23-08-040-801
4. Upper window removal (Refer to FIGURE 4/ GRAPHIC 25-23-08-991-004)
A. Remove valance panel according to Sogerma Spec. DIT/BC/2165/015/04.
B. Remove curtain cartridge according to Sogerma Spec. DIT/BC/2165/015/04.
C. To remove upper window attachment, refer to FIGURE 4/ GRAPHIC 25-23-08-991-004
steps 1 & 2. See page 3004
PAGE 3002
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
5.
TASK 25-23-08-040-802
Lower window removal (Refer FIGURE 4/ GRAPHIC 25-23-08-991-004)
RE 4/ GRAPHIC 25-23-08-991-004
PAGE 3003
JAN 10/05
A. To remove lower window attachment, refer FIGU
step 3. See next page.
Lou Martin & Assoc., Inc.
Component Maintenance Manual
FIGURE 4/ GRAPHIC 25-23-08-991-004
PAGE 3004
JAN 10/05
25-23-08
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
DISASSEMBLY
TASK 25-23-08-000-803
1. General
A. The overhaul instructions contained in this manual are usually implemented in
mechanical overhaul workshops.
B. Avoid removing identification plates, unless manufacturer authorization.
C. Only disassemble what is necessary to do the repairs or to replace defective part(s).
D. When applying the following instructions, never disassemble those components, which
have been proved to be in good condition after inspection unless their disassembly is
necessary to get access to the defective part.
E. All the parts must be identified before the disassembly in order to prevent the error and to
make the reassembly easier.
F. For the identification of damage or functional failure refer to:
“INSPECTION/REPLACEMENT & REPAIR” Page 7002
TASK 25-23-08-940-803
2. Job set-up information
A. Tools, fixtures, equipment and materials
None.
TASK 25-23-08-000-804
3. Preliminary Steps
A. Before the disassembly, put marks on all the parts to help the reassembly and to prevent
errors.
PAGE 4001
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
TASK 25-23-08-040-804
4. Decorative mask removal
A. Remove mask attachment screws from back side of window assy (5 places).
B. Gently move mask left or right to access and remove decorative handle screws.
C. Remove mask
NOTE: Assure the decorative mask & handles are protected at all times.
TASK 25-23-08-040-805
5. Inner lens removal
A. Remove screws holding the inner lens in place.
B. Remove inner lens protecting both sides from damage.
TASK 25-23-08-040-806
6. Blind mod. assy. removal
A. Locate Tension spring at lower back of window housing (reveal). Spring is secured in
place w/ stop nut & loop clamp.
B. To remove loop clamp, un-screw stop nut and slide clamp off retainer clip.
C. Slide loop clamp & shrink tube to side w/ spring to access tension assy.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
航空资料8(30)
