757
MAINTENANCE MANUAL
S 844-013
(6)
Move the inboard end of the reaction link aft to give clearance to remove the pin for the upper swivel.
S 014-014
(7)
Remove the nut with the crowfoot wrench (View D-D).
(a)
Install the thread protector.
(b)
Remove the pin to disconnect the upper swivel from the reaction link.
S 034-049
(8)
Lower the side strut and the downlock assembly with the hoist.
S 024-050
(9)
Remove the side strut and the downlock assembly.
S 014-016
(10)
Use the crowfoot wrench to remove the nut which connects the lower swivel to the shock strut (View E-E).
(a)
Install the thread protector.
(b)
Remove the lower swivel.
TASK 32-11-04-404-017
3. Install the Side Strut and Downlock Assembly on the Main Landing Gear_____________________________________________________________________ (Fig. 401)
A. Equipment
(1)
Thread Protector Set, MLG - B32011-14
(2)
Crowfoot Wrench - F70312-38
(3)
Boom Hoist - A20001-79
(4)
Drag Strut and Side Strut Sling Equipment, MLG
-
A32008-52
B.
Consumable Materials
(1) C00174 Corrosion Preventive Compound -MIL-C-16173, Grade 4
32-11-04
ALL ú ú 01 Page 405 ú Jan 28/00
A
757
MAINTENANCE MANUAL
(2)
D00633 Grease - BMS 3-33 (Recommended)
(3)
D00013 Grease - MIL-G-23827 (Alternative)
C.
References
(1)
AMM 07-11-01/201, Jacking Airplane
(2)
AMM 32-00-15/201, Landing Gear Door Locks
(3)
AMM 32-32-02/401, Main Gear Downlock Actuator
D.
Access
(1)
Location Zones
731/741 Main Landing Gear (MLG)
732/742 MLG Body Doors
733/743 MLG Oleo Doors
E.
Install the Side Strut and the Downlock Assembly
S 404-018
(1)
Install the thread protector.
S 644-034
(2)
Apply grease to the antirotation bolt, the washers, the nuts, the cotter pin, and the shaft of the swivel.
S 424-035
(3)
Install the lower swivel on the shock strut.
S 434-036
(4)
Use the crowfoot wrench to tighten the nut to 1800-2400 pound-inches (View E-E).
(a)
Loosen the nut then tighten it to 60-120 pound-inches to give clearance.
(b)
Loosen the nut to the nearest lock position to install the antirotation bolt.
S 844-019
(5)
Make sure there is a bolt through the downlock holes.
S 484-020
(6)
Install the sling equipment on the side strut and the downlock assembly. Use the instructions supplied with the tool.
(a)
Lift the side strut and the downlock assembly into its position on the main landing gear with the hoist.
S 624-021
(7) Apply the corrosion preventive compound to the inner diameter of the pins.
32-11-04
ALL ú ú 01 Page 406 ú Jan 28/00
A
757
MAINTENANCE MANUAL
(8) S 414-022Install the thread protector.
(9) S 644-037Apply grease to the pin, the antirotation bolt, the nuts, the washer, the bushing, and the cotter pin.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 起落架 CHAPTER 32 - LANDING GEAR 1(89)
