(2)
Install the PSEU on the E3-4 shelf.
S 864-012
(3)
Remove the DO-NOT-CLOSE tags and close these circuit breakers on the P11 panel:
(a)
AIRPLANES WITH ETOPS OR WITH TR SYNC LOCKS; 11B29, ENGINES RIGHT T/R IND
S 424-011
32-09-04
ALL ú ú 02 Page 404 ú Sep 28/99
A
757 MAINTENANCE MANUAL
(b)
AIRPLANES WITH ETOPS OR WITH TR SYNC LOCKS;
11B30, ENGINES RIGHT T/R CONT
(c)
AIRPLANES WITH ETOPS OR WITH TR SYNC LOCKS;
11C19, LANDING GEAR POS 2 ALTN
(d)
11C30, LANDING GEAR POS SYS 1
(e)
AIRPLANES WITH ETOPS OR WITH TR SYNC LOCKS;
11D11, ENGINES LEFT T/R IND
(f)
AIRPLANES WITH ETOPS OR WITH TR SYNC LOCKS;
11D12, ENGINES LEFT T/R CONT
(g)
AIRPLANES WITHOUT ETOPS OR TR SYNC LOCKS;
11K5, THRUST REVERSER IND
(h)
AIRPLANES WITHOUT ETOPS OR TR SYNC LOCKS;
11K6, THRUST REVERSER CONT
(i)
AIRPLANES WITHOUT ETOPS OR TR SYNC LOCKS;
11K32, THRUST REVERSER IND
(j)
AIRPLANES WITHOUT ETOPS OR TR SYNC LOCKS;
11K33, THRUST REVERSER CONT
(k)
11R33, DOOR IND
(l)
11R36, PROX SW TEST
(m)
11S23, POS SYS 2
S 864-013
(4)
Remove the DO-NOT-CLOSE tags and close this circuit breaker on the P34 panel:
(a)
34A5, CARGO DOOR CONT
S 444-024
(5)
Put the safety-sensitive systems back to their initial conditions (AMM 32-09-02/201).
D.
Test the PSEU
S 864-033
(1)
Supply electrical power (AMM 24-22-00/201).
S 744-034
(2)
Do these steps to test the PSEU:
(a)
Push the PRESS/TEST switch to do a lamp test on the PSEU front panel. Make sure the five indicator lights (SENSOR, CARD, TARGET, TARGET NEAR, TARGET FAR) come on and the 3-digit display shows the code 888.
(b)
If no light comes on and no code 888 is shown, then push the PRESS/TEST switch and TARGET TEST switch at the same time.
NOTE: When you push the PRESS/TEST and the TARGET TEST
____ switches together, the internal circuit of the PSEU sets the BITE.
32-09-04
ALL ú ú 02 Page 405 ú Sep 28/99
A
757
MAINTENANCE MANUAL
(c) To see the inflight faults, push the BIT switch until the code
000 shows.
(d) Write down each fault shown on the PSEU and the EICAS
status/maintenance messages.
NOTE:____ The display will show the code 000 or NO FAULTS or if
all the faults have been shown. All of the panel
indicators go off 2 minutes after they come on.
(e) Set the SENSOR CHANNEL SELECT DIALS on the PSEU to any code
other than the codes 500-505.
WARNING: DO THE DEACTIVATION PROCEDURE FOR THE SPOILERS OR MOVE ALL
_______ PERSONS AND EQUIPMENT AWAY FROM THE SPOILERS. THE SPOILERS CAN RETRACT QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 起落架 CHAPTER 32 - LANDING GEAR 1(56)
