S 024-006
(2)
Remove the bracket.
TASK 32-09-10-404-007
3. Install the Target Support Bracket for the Tilt Sensor on the Main Landing__________________________________________________________________________ Gear (Fig. 401)____
A. Consumable Materials
(1)
A00246, Sealant, Chromate - BMS 5-95 Type I
B.
References
(1)
32-00-15/201, Landing Gear Door Ground Operations and Locking Procedure
(2)
32-09-07/201, Main Gear Truck Tilt Sensors
C.
Access
(1)
Location Zones
731/741 Main Landing Gear (MLG)
732/742 MLG Body Doors
733/743 MLG Oleo Doors
D.
Install the Bracket
S 844-008
(1)
Do the steps that follow to install the bracket:
(a)
Apply the sealant to the faying surfaces.
(b)
Put the sealant on the threads of the bolts.
(c)
Install the bracket with the nuts and the bolts.
S 944-009
CAUTION: USE THE PROCEDURE IN AMM 32-09-07/201 TO MAKE SURE THE
_______ SENSOR/TARGET DISTANCE IS CORRECT. IF THE SENSOR/TARGET DISTANCE IS NOT IN TOLERANCE, THE AIR/GROUND RELAY SYSTEM WILL NOT OPERATE CORRECTLY.
(2) Make sure that the sensor/target distance is correct (Ref 32-09-07).
32-09-10
ALL ú ú 02 Page 403 ú May 28/01
A
757 MAINTENANCE MANUAL
E. Put the Airplane Back to Its Usual Condition
S 094-011 WARNING: USE THE PROCEDURE IN AMM 32-00-15/201 TO REMOVE THE DOOR LOCKS.
_______ THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1) Remove the door locks from the landing gear doors and close the doors (Ref 32-00-15).
32-09-10
ALL ú ú 01 Page 404 ú May 28/01
A
757 MAINTENANCE MANUAL
MAIN LANDING GEAR AND DOORS - DESCRIPTION AND OPERATION
_______________________________________________________
1. General_______
A. The main landing gear consists of two main gears (Ref 32-11-00) which absorb landing, taxiing, and take-off loads and support the airplane while on the ground. The gears are located on each side of the airplane and are mounted between the rear wing spar and the main landing gear beam. During flight, the gears retract inboard into the wing cavities and fuselage wheel wells and are covered by doors (Ref 32-12-00). The doors fair into the airplane body contour to reduce aerodynamic drag.
32-10-00
ALL ú ú 01 Page 1 ú Sep 15/82
A
757 FAULT ISOLATION/MAINT MANUAL
MAIN LANDING GEAR AND DOORS
COMPONENT SHT 102 FIG. QTY ACCESS/AREA REFERENCE
BEARING - MAIN GEAR AFT TRUNNION 2 2 MAIN LANDING GEAR 32-11-01
BEARING - MAIN GEAR FORWARD TRUNNION 2 2 MAIN LANDING GEAR 32-11-01
DOOR - MAIN GEAR 2 2 GEAR WHEEL WELL OF THE MAIN LANDING 32-12-01
DOOR - MAIN GEAR STRUT 1 2 MAIN LANDING GEAR 32-12-04
DOOR - MAIN GEAR TRUNNION FAIRING 2 2 MAIN LANDING GEAR 32-12-10
GEAR - MAIN 1 & 2 2 MAIN LANDING GEAR 32-11-01
LINK - MAIN GEAR LOWER DOWNLOCK 1 2 MAIN LANDING GEAR 32-11-13
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 起落架 CHAPTER 32 - LANDING GEAR 1(73)
