(b)
Set orientation of the Connector (03-010) (Ref. to Fig. 1) and install the Connector (03-010), the Supports (01-080), the Washers (01-160) and the Screws (01-120), (01-140) with locking compound (M14A) LOCTITE 222.
(c)
Install the Washer (01-150), the Screw (01-130), the Lug (03-020) and the Nut (01-170).
(d)
Install the Lug (01-180), the Supports (01-080), the Washers (01-110) and the Screws (01-090), (01-100) to the Cover (01-270).
(e)
Set the fork of the Equipped Ball-Screw (02-310) lined-up in the Guide (01-230).
(f)
Carefully set the Grommet (03-620) at the Cover (01-260).
(g)
Install the Cover Assembly (01-190), the Washers (01-220) and the Screws (01-200) and (01-210) with locking compound (M14A) LOCTITE 222.
(h)
For versions ABC, carefully set the motor to the plate and install the Washers (01-350) and the Screws (01-330), (01-350) with locking compound (M14A) LOCTITE 222.
Subtask 21-53-12-420-003-A01
(16) Installation of varnish and lockwires
(a)
Apply varnish (M01D) 6060 BT519 GREEN to the screws (Ref. to Fig. 7008).
(b)
Install lockwires (01-030) to the screws (Ref. to Fig. 7008).
Page 7028
ACTUATOR - VARNISH AND LOCKWIRES LOCATION- VERSION ABC (Sheet 1 of 2)
Figure 7008/GRAPHIC 21-53-12-991-025-A01
Page 7029
21-53-12 JUN 15/10
ACTUATOR - VARNISH AND LOCKWIRES LOCATION- VERSION DE (Sheet 2 of 2)
Figure 7008/GRAPHIC 21-53-12-991-025-A01
Page 7030
E. Close-Up Subtask 21-53-12-750-009-A01
(1) Check after assembly
(a)
Make sure that the nut A is tighten at a torque value of 6 -0/+ 2 N.m
(53.12 - 0/+ 17.70 lbf.in).
(b)
Do a entire test after assembly (refer to TASK 21-53-12-700-801-A01).
Page 7031 / 7032
21-53-12 JUN 15/10
FITS AND CLEARANCES
TASK 21-53-12-920-801-A01
1. ACTUATOR - FITS AND CLEARANCES
A. Clearances
NOTE: The values given in the following tables are for information only.
(1) Lateral clearance for the gears (03-370), (03-420) and (03-470): between 0,1 and 0,3 mm (0.0039 and 0.0118 in.)
B. Fits And Clearances Table
CAUTION: REPAIR OR REPLACE THE PARTS WHICH ARE NOT WITHIN THE LIMITS GIVEN ((REFER TO PAGE BLOCK 3001), (REFER TO PAGE BLOCK 6001), (REFER TO PAGE BLOCK 7001)).
NOTE: The values given in the following tables are for information only.
(1) How to Use the Fits and Clearances Table
(a)
Column 1 gives the figure number, and the reference letter of the section with the location number of the part.
(b)
Column 2 contains IPL/IPC figure and item numbers of the mating parts.
(c)
Column 3 gives the initial manufacturers limits for the dimensions and assembly clearances. A minus (.) sign shows an interference fit.
(d)
Column 4 gives the in-service wear limits for dimensions and maximum allowable clearances. A minus (.) sign shows an interference fit.
Page 8001
21-53-12 JUN 15/10
(2) This section gives fits and clearances data (Ref. to Fig. 8001).
1 2 MATING 3 MFR LIMITS 4 IN-SERVICE WEAR LIMITS
DIMENSION mm (in) ASSEMBLY CLEARANCE mm (in) DIMENSION LIMITS mm (in) MAX ALLOWABLE CLEARANCE mm (in)
MIN MAX MIN MAX MIN MAX
A OD (02-320) 35,975 (1.4163) 35,991 (1.4169) 0.009 (0.00035) 0.050 (0.00197)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：LIEBHERR-AEROSPACE TOULOUSE SAS COMPONENT MAINTENANCE MANUAL(39)
