LIEBHERR-AEROSPACE TOULOUSE SAS COMPONENT MAINTENANCE MANUAL(35)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

(e) Carefully apply heat locally to install the Heat-shrinking sleeves.
(f) Install the Spacers (03-520) and (03-530) with locking compound (M14A) LOCTITE 222.
(g) Install the Spacers (03-490), the Washers (03-510) and the Screws (03-500) with locking compound (M14A) LOCTITE 222.
(h) Lightly apply grease (M26C) AEROSHELL 7 to the Bearings (03-480).
(i) Install the Bearings (03-480) to the Plate (03-600).
(j) Lightly apply grease (M26C) AEROSHELL 7 to the cogs of:
- the Gear (03-350) or the Gear Assembly (03-370)
- the Gear (03-400) or the Gear Assembly (03-420)
- the Gear (03-450) or the Gear Assembly (03-470)
(k) Install:
- the Spacer (03-340) with the Gear (03-350) with the Spacer (03-360) with the Shaft (03-330)
- or the Gear Assembly (03-370).
(l) Install:
- the Spacer (03-410) with the Gear (03-400) with the Spacer (03-390) with the Shaft (03-380)
- or the Gear Assembly (03-420).
(m) Install:
- the Spacer (03-460) with the Gear (03-450) with the Spacer (03-340) with the Shaft (03-430)
- or the Gear Assembly (03-470).
(n) Lightly apply grease (M26C) AEROSHELL 7 to the Bearings (03-320).
(o) Install the Bearings (03-320) to the Plate (03-300).
Page 7011
21-53-12  JUN 15/10
(p)
Install the Plate (03-300) and the Screws  (03-310) with locking compound (M14A) LOCTITE 222.

(q)
Make sure that the lateral play of the gears is 0,2 ± 0,1 mm (0.00787 ± 0.00394 in).

Page 7012

(03-480) (03-330) (03-360) (03-350) (03-340) (03-320) (03-370)

ACTUATOR - INSTALLATION OF GEARS
Figure 7003/GRAPHIC 21-53-12-991-020-A01

Page 7013
21-53-12 JUN 15/10
Subtask 21-53-12-440-004-A01
(6) Assembly of the Wiring Assembly (01-300)
CAUTION: CLEAN PART TAPPING TO BE ATTACHED WITH INOX SCREWS.
CAUTION: MAKE SURE THERE IS NO LOCTITE 222 LOCKING COMPOUND IN CONTACT WITH THE CASE OF THE SWITCHES (03-140) AND (03-180). LOCTITE 222 LOCKING COMPOUND CAN DAMAGE THE CASE OF SWITCHES.
CAUTION: DO NOT DAMAGE THE BLADES (03-130) DURING ASSEMBLY. FOR NO CONTACT WITH THE CAMS, THE BLADE RADIUS MUST BE 45 MM (1.7716 IN).
CAUTION: USE HIGH TEMPERATURE CLASS 5 A GRADE 3 SOLDER (SN5-PB93,5-AG1,5) ONLY FOR WIRE TYPE 2619 (NOT APPLICABLE FOR BLACK WIRE TYPE 2219).
(a)
 Install the Support (03-270) and the Screws (03-280) with locking  compound (M14A) LOCTITE 222.

(b)
For versions A, B and C (Ref. to Fig. 7004 Sheet 1 of 2), install the Washer (03-260), the Cam (03-240A), the Washer (03-230), the Cam (03-210A), and the Screws (03-220), (03-250) with locking compound (M14A) LOCTITE 222. Do not tighten the Screws (03-220), (03-250) to allow adjustment.

(c)
For versions D and E (Ref. to Fig. 7004 Sheet 2 of 2), install the Washer (03-260), the Cam (03-210B), the Washer (03-230), the Cam (03-240B), and the Screws (03-220), (03-250) with locking compound (M14A) LOCTITE 222. Do not tighten the Screws (03-220), (03-250) to allow adjustment.

(d)
Clean to 4 tapping of the Support (03-270) with DYNAFAST cleaning solvent.

(e)
Clean the Screws (03-150) with DYNAFAST cleaning solvent.

(f)  
Install the Shim (03-170), the Switch (03-140) with one Blade (03-130), the Washers (03-160) and the Screws (03-150) with locking compound (M14A) LOCTITE 222.

(g)
Clean the Screws (03-190) with DYNAFAST cleaning solvent.

(h)
Install the Switch (03-180) with one Blade (03-130), the Washers (03-200) and the Screws (03-190) with locking compound (M14A) LOCTITE 222.

(i)  
Set 15 mm (0.5905 in) length of Heat-shrinking sleeves (black) RNF100 1/4 NOIRE TYPE1 on the Spacers (03-090).

(j)  
Carefully apply heat locally to install the Heat-shrinking sleeves.
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：LIEBHERR-AEROSPACE TOULOUSE SAS COMPONENT MAINTENANCE MANUAL(35)