Page 1026
F. Close-Up Subtask 21-53-12-750-008-A01
(1) Delivery And Configuration Procedure
(a) For versions ABC
ACTION RESULT
1 Set the Electrical Test Set-Up to get a displacement speed near 1 mm/s (0.0394 in/s).
2 Set the actuator to the MECHANICAL STOP EXTENDED position (door fully closed) (Ref. to Fig. 1002).
3 Remove the actuator from the bench.
4 Install the protection sleeve on the actuator.
5 Install a plastic cap on the electrical connector.
6 (Rod-end nut at a torque of 6 N.m (- 0/+ 2) (53.10 lb.in (- 0/+ 17.7))).
(b) For versions DE
ACTION RESULT
1 Set the Electrical Test Set-Up to get a displacement speed near 1 mm/s (0.0394 in/s).
2 Set the actuator to the MECHANICAL STOP RETRACTED position (door fully closed) (Ref. to Fig. 1003).
3 Remove the actuator from the bench.
4 Install a plastic cap on the electrical connector.
5 (Rod-end nut at a torque of 6 N.m (- 0/+ 2) (53.10 lb.in (- 0/+ 17.7))).
Page 1027
21-53-12 JUN 15/10
TASK 21-53-12-810-801-A01
2. ACTUATOR - FAULT ISOLATION
A. Reason For The Job
Self-Explanatory
B. Job Set-Up Information
(1)
Tools, Features And Equipment Not Applicable
(2)
Consumable Material Not Applicable
(3)
Referenced Information
REFERENCE PAGE BLOCK DESIGNATION
(refer to Subtask 21-53-12-210-001-A01) 1001 VISUAL CHECK
(refer to Subtask 21-53-12-700-005-A01) 1001 MOTOR IMPEDANCE TEST
(refer to Subtask 21-53-12-700-006-A01) 1001 BRAKE COIL IMPEDANCE TEST
(refer to Subtask 21-53-12-750-001-A01) 1001 CASE BONDING TEST
(refer to Subtask 21-53-12-750-002-A01) 1001 INSULATION TEST
(refer to Subtask 21-53-12-750-003-A01) 1001 STROKES, MICROSWITCHES, AND POTENTIOMETER TEST
(refer to Subtask 21-53-12-750-004-A01) 1001 POTENTIOMETER SPIKE TEST
(refer to Subtask 21-53-12-750-005-A01) 1001 FAST CLOSURE TEST (FOR VERSIONS ABC ONLY)
(refer to Subtask 21-53-12-750-006-A01) 1001 MAXIMUM LOAD TEST
(refer to Subtask 21-53-12-750-007-A01) 1001 CLUTCH EFFICIENCY TEST
C. Job Set-Up Not Applicable Page 1028
21-53-12 JUN 15/10 D. Procedures
TEST POSSIBLE CAUSE ACTION
Visual Check (refer to Subtask 21-53-12-210-001-A01) Cover Repair the cover
Ball-screw Do the adjustment of the ball-screw
Motor Impedance Test (refer to Subtask 21-53-12-700-005-A01) Motor Replace the motor
Brake Coil Impedance Test (refer to Subtask 21-53-12-700-006-A01) Brake Replace the brake
Replace the motor
Case Bonding Test (refer to Subtask 21-53-12-750-001-A01) Bonding Lug Replace the bonding lug
Insulation Test (refer to Subtask 21-53-12-750-002-A01) Wiring Do a check of the wiring
Connector Replace the connector
Strokes, Microswitches, Potentiometer Test (refer to Subtask 21-53-12-750-003-A01) Wiring Do a check of the wiring
Connector Replace the connector
Potentiometer Replace the potentiometer
Microswitches Do the adjustment of the microswitches
Replace the microswitches
Ball-screw Do the adjustment of the ball-screw
Replace the ball-screw
Motor Do the adjustment of the motor brake
Replace the motor
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：LIEBHERR-AEROSPACE TOULOUSE SAS COMPONENT MAINTENANCE MANUAL(20)
