D. Procedure
WARNING: THE ELECTRICAL TEST SET-UP USES 115 VAC VOLTAGES. OBEY STANDARD PROCEDURES TO WORK WITH HIGH VOLTAGE.
CAUTION: PLACE THE COMPONENT ON A CLEAN WORKBENCH, IN A DUST-FREE AND MOISTURE-FREE ROOM. HANDLE ALL PARTS CAREFULLY, AND PROTECT THEM AGAINST CORROSION AND IMPACT DAMAGE AFTER DISASSEMBLY.
CAUTION: EXAMINE THE PARTS TO MAKE SURE THAT THEY ARE SERVICEABLE AND HAVE THE CORRECT PART NUMBER. MAKE SURE THAT THE PARTS ARE CLEAN AND THERE IS NO PRESERVATION MATERIAL REMAINING.
CAUTION: ELECTRICAL CONNECTIONS ARE MADE USING THE MINIMUM AMOUNT OF SOLDER (TYPE SN63 PB37) NECESSARY TO EFFECT A CORRECT JOINT. AFTER SOLDERING, BRUSH THE SOLDERED JOINT AND THE SURROUNDING AREA WITH THE SPECIFIED CLEANSER TO REMOVE UNWANTED MATERIALS AND SOLDER. DRY WITH A LOW PRESSURE AIR JET.
CAUTION: WHEN SOLDERING, CONFINE THE HEAT, AS MUCH AS POSSIBLE, TO A LIMITED AREA AT ONE TIME. USE TEMPERATURE CONTROLLED SOLDERING IRONS AND HEAT SHUNTS TO PROTECT THE COMPONENTS FROM THE EFFECTS OF HEAT.
Page 7004
CAUTION: FOR TIGHTENING VALUE OF PARTS, REFER TO THE TABLE OF TIGHTENING TORQUES IN PAGE BLOCK - FITS AND CLEARANCES (REFER TO TASK 21-53-12-920-802-A01) FOR DETAIL OF TORQUE APPLIED TO THE SCREWS. LOCK ALL SCREW WITH THE SPECIFIED LOCKING COMPOUND.
CAUTION: REPLACE ALL THE SPRINGS AND THE LOCK WASHERS.
NOTE: THE NUMBERS IN PARENTHESIS AFTER THE COMPONENT DESCRIPTION ARE THE FIGURE AND THE ITEM NUMBERS OF THE IPL (refer to Page Block 10001).
Subtask 21-53-12-440-001-A01
(1) Assembly of the Motor (03-610B)
CAUTION: BE CAREFUL TO THE ELECTRICAL WIRES WHEN YOU INSTALL THE ROTOR AND THE ELECTROMAGNETIC BRAKE.
(a)
Set the Rotor Assembly (05-160) in the Stator Crankcase Assembly (05-240).
(b)
Install the Ball Bearing (05-220) on the Rotor Assembly (05-160). NOTE: (refer to TASK 21-53-12-300-803-A01) for replacement of the bearing.
(c)
Install the Washers (05-200) and (05-210).
(d)
Install the Seal (05-170), the Flange (05-180) and the Screws (05-190) with locking compound (M14A) LOCTITE 222.
(e)
Install the ball Bearing (05-150) in the Coil Assembly (05-100). NOTE: (refer to TASK 21-53-12-300-803-A01) for replacement of the bearing.
(f)
Install the Flange (05-130) and the Screws (05-140) with locking compound (M14A) LOCTITE 222.
(g)
If necessary connect the electrical wires to the Coil Assembly (05-100).
(h)
Install the Coil Assembly (05-100), the Washers (05-120) and Screws (05-110) with locking compound (M14A) LOCTITE 222.
(i)
Install the Spacer (05-090), the Spring (05-070), the Washer (05-080), the Brake Framework Assembly (05-060) and the Disc Brake (05-040).
(j)
Install the Nut (05-050) with a torque value of 3,25 N.m (28.76 lbf.in) and with locking compound (M14A) LOCTITE 222.
(k)
Do the Adjustment of the Brake Framework (refer to Subtask 21-53-12-820-001-A01).
(l)
Set sealing compound CAF 730 to the Cover (05-010).
(m) Install the Cover (05-010), the Washers (05-030) and the Screws (05-020). Subtask 21-53-12-820-001-A01
(2) Adjustment of the brake framework of the Motor (03-610B)
(a) Obey the procedure that follows to do the adjustment of the brake framework:
Page 7005
21-53-12 JUN 15/10
1 Deactivate the Brake Framework (apply 28 VDC between the pin T and the pin U of the connector).
2 Measure and record the value E (Ref. to Fig. 7001).
3 Activate the Brake Framework (remove the 28 VDC from the pin T and the pin U of the connector).
4 Make sure that the Value E = 0,15 ± 0,03 mm (0.0059 ± 0.0012 in).
5 If necessary, replace the Washer (05-080) by a Washer (05-081) or (05-082) to get the Value E = 0,15 ± 0,03 mm (0.0059 ± 0.0012 in).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：LIEBHERR-AEROSPACE TOULOUSE SAS COMPONENT MAINTENANCE MANUAL(33)
