09P1181B
09P1181A
09P1180
Roller Bearing (02-390)
Case (02-450)
ACTUATOR- INSTALLATION OF THE ROLLER BEARING (02-390) (Sheet 3 of 4)
Figure 6001/GRAPHIC 21-53-12-991-015-A01
Page 6006
02-430 02-440 02-410 02-450B
ACTUATOR- BEARINGS AND LIP SEAL LOCATION (Sheet 4 of 4)
Figure 6001/GRAPHIC 21-53-12-991-015-A01
Page 6007 / 6008
21-53-12 JUN 15/10
TASK 21-53-12-300-802-A01
2. REPAIR 02 - ACTUATOR - REPLACEMENT OF EQUIPPED PLATE PARTS
A. Reason For The Job
(1) Use this procedure when it becomes necessary to replace the Equipped Plate parts.
B. Job Set-Up Information
(1)
Tools, Features and Equipment
(a) Equivalent alternatives may be used for the listed items.
(2)
Consumable Material
REFERENCE QTY NAME
09P1231 1 Removal tool for lip seal and roller bearing
09P1181A 1 Installation tool for roller bearing
09P1181B 1 Installation tool adaptor
09P1180 1 Centering tool
09P1524 1 Removal plate tool
No specific 1 Hydraulic press
No specific 1 Heating unit
No specific 1 Manual press
(a) Equivalent alternatives may be used for the listed items.
REFERENCE NAME
95° ETHYL ALCOHOL Cleaning fluid
(M26C) AEROSHELL 7 Grease
Page 6009
21-53-12 JUN 15/10
(3) Referenced Information
REFERENCE PAGE BLOCK DESIGNATION
(refer to Page Block 10001) 10001 ILLUSTRATED PARTS LIST
(Ref. to Fig. 6002) 6001 ACTUATOR - REMOVAL AND INSTALLATION OF THE LIP SEAL (02-070) AND OF THE ROLLER BEARING (02-060)
C. Job Set-Up Not Applicable
D. Procedures WARNING: PROTECT YOURSELF WHEN YOU TOUCH THE PLATE (02-150) AT 150 °C
(320 °F). CAUTION: DO NOT APPLY HEAT LONGER THAN NECESSARY. NOTE: CLEAN ALL METALLIC SURFACES BY USING 95° ETHYL ALCOHOL CLEANING
FLUID BEFORE INSTALLATION. NOTE: THE NUMBERS IN PARENTHESIS AFTER THE COMPONENT DESCRIPTION ARE THE FIGURE AND THE ITEM NUMBERS OF THE IPL (refer to Page Block 10001). Subtask 21-53-12-350-003-A01
(1) Removal
(a)
Lightly tap the plate to remove the Ball Bearings (02-080), (02-090), (02-100) and if applicable (02-100) and (02-110).
(b)
Heat the plate to remove the 3 Pins (02-050).
(c)
If necessary, install the Plate (02-150) in a Heating Unit at 150 °C (320 °F) for 1 h.
(d)
If necessary, lightly apply grease AEROSHELL 7 (M26C) to the special tool 09P1231.
(e)
Remove the Lip Seal (02-070) and the Roller Bearing (02-060) with the special tool 09P1231 and a Hydraulic Press (Ref. to Fig. 6002).
Subtask 21-53-12-350-004-A01
(2) Installation
(a) Installation of the Roller Bearing and Lip Seal
1
Install the Plate (02-150) in a Heating Unit at 150 °C (320 °F) for 1 h. 2
Lightly apply grease AEROSHELL 7 (M26C) to the Lip Seal (02-070) (at outer diameter).
Page 6010
3 Set the Plate (02-150) on the special tool 09P1524 (Ref. to Fig. 6002).
4 Set the Lip Seal (02-070) on the special tools 09P1180, 09P1181A and 09P1181B.
5 Carefully install the Lip Seal (02-070) in the Plate (02-150) with a Hydraulic Press set
to 200 daN (449 lbf). 6 Make sure that the Lip Seal (02-070) is fully in contact with the Plate (02-150). 7 Remove the special tools. 8 Lightly apply grease AEROSHELL 7 (M26C) to the Roller Bearing (02-060) (at outer
diameter). 9 Set the Roller Bearing (02-060) on the special tools 09P1180, 09P1181A and 09P1181B. 10 Carefully install the Roller Bearing (02-060) in the Plate (02-150) with a Hydraulic
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：LIEBHERR-AEROSPACE TOULOUSE SAS COMPONENT MAINTENANCE MANUAL(29)
