R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-46Page 450 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 27-54-46-860-058
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Make sure that the flaps are fully retracted (Ref. TASK 27-50-00-866-009).
(2)
Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER is attached to the flap/slat control lever on the panel 114VU.
(3)
Make sure that the applicable MLG door is open (Ref. TASK 32-12-00-010-001).
(4)
Make sure that a GROUND LOCK SLEEVE is installed on the applicable actuating cylinder (Ref. TASK 32-00-00-481-002).
(5) Make sure that the access platform is in the applicable position. Subtask 27-54-46-865-060
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
4. Procedure
_________ (Ref. Fig. 403/TASK 27-54-46-991-004, 404/TASK 27-54-46-991-006) R **ON A/C 062-099, 104-149, 151-199, 204-299, 401-499,
(Ref. Fig. 405/TASK 27-54-46-991-007)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-46Page 451 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 27-54-46-420-056
A. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2)
Make sure that the No.1 flap track carriage is in the correct condition.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
Do an inspection of the component interface and/or the adjacent area.
**ON A/C 001-049, 051-061, 101-103, 201-203,
Subtask 27-54-46-420-057
B. Installation of the Pendulum of the No.1 Flap Track Carriage
(Ref. Fig. 403/TASK 27-54-46-991-004)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME DAMAGED OR
_______ INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-46Page 452 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(1)
Apply COMMON GREASE (Material No. 04-004) to the three part bearing at the top of the pendulum (7).
(2)
Put the pendulum (7) in the carriage (6).
(3)
Apply COMMON GREASE (Material No. 04-004) to the bolt (17) and apply SEALANTS (Material No. 09-013) to the new lockplate (16).
(4)
Install the bolt (17) and the new lockplate (16) through the lower
side of the flap track beam (19).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵5(77)
