(Ref. Fig. 401/TASK 27-54-45-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 27-54-45-991-001-A)
**ON A/C ALL
Subtask 27-54-45-410-058
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the COLLAR-SAFETY, SPOILER from the piston rod of the servo-control.
(3)
Put the applicable spoiler back to the 'O' (Operation) position (Ref. TASK 27-60-00-866-002).
(4)
On the servo-control, make sure that the pointer on the hex-head is opposite the letter 'O' (Operation) on the housing.
(5)
Install the applicable access panel (Ref. TASK 57-51-37-400-004):
-
FOR 6222CM
install 575CB
-
FOR 6272CM
install 675CB.
Subtask 27-54-45-942-059
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-54-45Page A430 1 1 Aug 01/02R 1 1 1CES 1
TASK 27-54-45-000-011
Removal of the Torque Shafts 6224CM(6274CM)/6230CM(6280CM)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning sign No specific access platform 3.0 m (9 ft. 10 in.) 98D27604000000 1 COLLAR-SAFETY, SPOILER 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
1EFF : ALL 1 27-54-45Page A431 1 1 Aug 01/02R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground
27-54-44-000-002 Removal of the Steady Bearings FIN 6215CM(6265CM)/6219CM(6269CM)/6223CM (6273CM)/6225CM(6275CM)/6229CM(6279CM)/6231CM(6281CM)
27-60-00-866-002 Extension-Retraction of the Spoilers for Maintenance
**ON A/C 001-049, 051-061, 101-103, 201-203,
27-54-45-991-001 Fig. 401 R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
27-54-45-991-001-A Fig. 401A
**ON A/C ALL
27-54-45-991-004 Fig. 405
3. Job Set-up
__________
**ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 401/TASK 27-54-45-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 27-54-45-991-001-A) **ON A/C ALL
Subtask 27-54-45-941-076
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning sign in position to tell persons not to operate the flap/slat controls.
Subtask 27-54-45-860-060
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Extend the flaps fully (Ref. TASK 27-50-00-866-008).
(2)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) on the flap/slat control lever.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵5(53)
