REFERENCE DESIGNATION
-------------------------------------------------------------------------------
**ON A/C 001-049, 051-061, 101-103, 201-203,
27-54-45-991-003 Fig. 404 R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
27-54-45-991-003-A Fig. 404A
**ON A/C ALL
3. Job Set-up
__________
**ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 401/TASK 27-54-45-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 27-54-45-991-001-A)
**ON A/C ALL
Subtask 27-54-45-941-089
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position to tell persons not to operate the flap/slat controls.
Subtask 27-54-45-860-075
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Make sure that the flaps are fully retracted (Ref. TASK 27-50-00-866-009).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is on the flap/slat control lever on panel 114VU.
(3)
Make sure that the access platform is in the applicable position.
(4)
Make sure that the applicable access panels are removed (Ref. TASK 57-51-37-000-004):
-
for 6232CM, panels 575FB, 575GB
-
for 6282CM, panels 675FB, 675GB.
(5)
Make sure that the applicable spoiler is in the 'M' (Maintenance) position (Ref. TASK 27-60-00-866-002).
(6)
Make sure that the COLLAR-SAFETY, SPOILER is on the piston rod of the servo-control.
Subtask 27-54-45-865-097
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-54-45-480-051
D. Support Equipment
(1) Make sure that the PIN RIGGING-FLAPS (TRACK 1) is installed at the flap track 1 position.
**ON A/C 301-399,
Subtask 27-54-45-480-051-A
D. Support Equipment
(1) Make sure that the PIN RIGGING FLAPS is installed at the flap track 1 position.
**ON A/C ALL
4. Procedure
_________
**ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 404/TASK 27-54-45-991-003) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 404A/TASK 27-54-45-991-003-A)
**ON A/C ALL
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 27-54-45-420-075
A. Preparation for Installation
CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT.
_______
GREASE AND ASSEMBLY PASTE DO NOT MIX.
(1)
Clean the parts:
(a) Use a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean:
-
the nuts (59)
-
the bolts (60)
-
the flanges of the universal joint (57) and the torque shaft (58).
(2)
Dry the parts: WARNING : USE A PROTECTIVE EYE SHIELD/GOGGLES WHEN YOU USE COMPRESSED
_______ AIR. DEBRIS AND/OR HIGH PRESSURE AIR CAN DAMAGE YOUR EYES.
WARNING : DO NOT PUT COMPRESSED GAS IN CONTACT WITH YOUR SKIN. THE
_______ GAS CAN GO THROUGH THE SKIN AND MAKE BUBBLES IN THE BLOOD. THIS CONDITION CAN KILL YOU.
(a) Use compressed air to dry the cleaned areas.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(5)
Do one of the steps that follow:
CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT.
_______
GREASE AND ASSEMBLY PASTE DO NOT MIX.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵5(62)
