曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
Q. Torque collar screws (item 4) to 160.0 ±5.0 in-lb (18.1 ±0.6 Nm).
R. Rotate FLAPS switch to UP position.
S. Set MASTER SWITCH to OFF position.
T. Install access panels CF4C and CF5. (Refer to AMM 06-00)
U. Install carpet. (Refer to AMM 25-10)
V. Install passenger seats. (Refer to AMM 25-10)
W. Complete airplane records by noting compliance with SB 2X-27-16 in Aircraft Logbook.
C I R R U S S E R V I C E B U L L E T I N MOD E L S R 2 X S E R I E S
SB 2X-27-16
Cirrus Design SR20 Serials 1005 thru 2029. Page 4
Cirrus Design SR22 Serials 0002 thru 3459.
EFFECTIVITY:
October 02, 2009
Figure 01
Flap Actuator Modification (Page 1 of 2)
0%
50%
100%
6
SR2_SB27_1281
LEGEND
1. End Fitting
2. Rod End
3. Shaft Collar
4. Screw
5. Castellated Nut
6. Cotter Pin
7. Existing Washer
8. Existing Bolt
9. Existing Jam Nut
NOTE
Bottom out end fitting on actuator to ensure maximum thread engagement.
Bottom out rod end in end fitting. During adjustment, rod end may need to
be backed out a maximum of 2 turns.
1
9
9
7
7
7
7
2
8
5
3
3
4
TORQUE TUBE
COUPLER (REF)
PROXIMITY SENSOR
(REF)
4
C I R R U S S E R V I C E B U L L E T I N MOD E L S R 2 X S E R I E S
SB 2X-27-16
Cirrus Design SR20 Serials 1005 thru 2029. Page 5
Cirrus Design SR22 Serials 0002 thru 3459.
EFFECTIVITY:
October 02, 2009
Figure 01
Flap Actuator Modification (Page 2 of 2)
0.05 inch
(1.27 mm)
MINIMUM
SR2_SB27_1282
NOTE
With flaps in 100% position, install shaft collar on actuator shaft with
0.05 ±0.01 inch (1.27 ±0.25 mm) gap between face of collar and actuator seal.
With flaps in UP position, ensure a minimum gap of 0.05 inch (1.27 mm) exists
between end fitting and torque tube coupler.
TORQUE TUBE
COUPLER
(REF)
0.05 ±0.01 inch
(1.27 ±0.25 mm)
END FITTING
(REF)
ACTUATOR SEAL
(REF)
SHAFT COLLAR
(REF)
C I R R U S SR2X
Service Bulletin
Use this form to submit a Publications Change Request to our Engineering Department and/or to tell us what
you think of the quality of this publication. We will use the data you provide us to improve the quality of our technical
publications.
Number: SB 2X-27-16 Service Loop Evaluation Form
Contact Information:
Organization: _________________________________ Today’s Date: __________________________
Address: ____________________________________ Telephone No.: _________________________
City/ST/Zip: __________________________________ Fax No: _______________________________
Prepared By: _________________________________ E-Mail: _______________________________
Title:________________________________________
Location of Publication Change Request:
Chapter Number: Section Number: Figure No (IPC or WM only): ___________________
Page Number: Page Date: Illustration Number (if applicable): _______________
Please consider the following suggestions for change:
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Evaluation:
Please rate the quality of this publication. (good) 4 3 2 1 (poor)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Cirrus Design SR20西锐20飞行员操作手册和飞机飞行手册附录(123)
