曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
1001086 R-I0520F3B
1001087 R-I0550D27B
1001092 R-I0550D24B
1001093 R-I0550D24B
1001094 R-I0520D112B
1001095 I0520BB16B
1001096 R-I0520A5B
1001097 TSI0520C6B
1001098 R-TSI0550C14B
1001101 I0550N19B
1001102 LTSI0520AE3B
1001103 R-0470S2K
1001104 TSI0520R9B
1001105 I0520F64B
1001108 R-I0520D116B
1001109 R-I0470L21B
1001110 R-I0520L47B
Engine Serial Number Engine Model
NOTE: “R-” prefix indicates rebuilt.
“EX” suffix indicates both the intake and exhaust lifter
inspection is required.
1001112 R-TSI0520VB10F
1001113 R-TSI0520VB9F
1001114 R-TSI0520VB9F
1001119 R-I0550B89B
1001120 R-I0520F43B
1001121 R-I0520F6B
1001122 R-I0520E2B
1001124 R-TSI0520EB9B
1001125 R-I0550D13B
1001127 R-I0470L21B
1001128 R-I0470L21B
1001129 R-I0520D35B
1001133 I0550C70B
1001134 I0550C70B
1001135 I0550C70B
1001136 I0550C70B
1001138 I0520F12B
1001141 R-I0520CB31B
1001142 R-I0550P3B
1001145 R-GTSI0520M2B
1001146 EX R-TSI0360EB1B
1001147 R-TSI0520R9B
1001149 R-0470S2B
1001150 R-I0470V09B
1001151 R-I0520F27B
1001152 R-I0520F43B
1001153 R-I0550B75B
1001155 R-TSI0520M7B
1001157 EX TSI0360RB1B
1001158 R-0470R25B
1001159 R-I0520F83B
1001160 R-I0520D40B
1001161 R-I0550F37B
1001162 R-0470U17B
1001163 0470R78B
1001164 R-I0520BB15B
1001165 R-I0470L21B
1001172 R-I0550C71B
1001174 I0550D15B
1001175 R-I0550B82B
1001177 EX R-TSI0360LB1B
1001187 EX R-TSI0360FB1B
1001188 R-I0520CB36B
1001189 R-0470S2B
1001191 R-I0520BB6B
1001193 R-I0520BB15B
ISSUE DATE REVISION DATE PAGE NO REVISION
12 of 20
03 Nov 2009 TM
PO BOX 90, Mobile, AL 36601 251-438-3411 MSB09-8
©2009, TELEDYNE CONTINENTAL MOTORS, INC.
Engine Serial Number Engine Model
NOTE: “R-” prefix indicates rebuilt.
“EX” suffix indicates both the intake and exhaust lifter
inspection is required.
1001194 R-I0520C7B
1001195 R-I0520C7B
1001197 EX R-I0360GB3B
1001200 R-I0520F12B
1001202 I0550B4F
Engine Serial Number Engine Model
NOTE: “R-” prefix indicates rebuilt.
“EX” suffix indicates both the intake and exhaust lifter
inspection is required.
1001210 R-0470R74B
1001213 I0550C31B
1001236 EX TSI0360EB1B
ISSUE DATE REVISION DATE PAGE NO REVISION
13 of 20
03 Nov 2009 TM
PO BOX 90, Mobile, AL 36601 251-438-3411 MSB09-8
©2009, TELEDYNE CONTINENTAL MOTORS, INC.
Section B. Removal and Installation Instructions
WARNING
Turn the Ignition Switch to the OFF position and disconnect
engine electrical power prior to commencing maintenance. Do
not stand or place equipment within the rotational arc of the
propeller.
B.1. Hydraulic Lifter Removal
B.1.a. Updraft Cylinder Lifter Removal
NOTE: Remove only those components related to the “Intake”
valve train unless exhaust lifter inspection is required as indicated
in Step 2, paragraph 1.
Procedure
1. Remove cowling and any airframe supplied accessories in accordance with the
airframe manufacturer's instructions to gain access to the cylinder.
2. Disconnect the battery according to the airframe manufacturer's instructions.
3. Disconnect all spark plug leads and remove the upper spark plug from each cylinder.
4. Remove the rocker cover fasteners and rocker covers from the cylinder.
5. Remove and discard the rocker cover gaskets.
6. Position the crankshaft so the piston is at top dead center and both intake and exhaust
valves of the cylinder being disassembled are closed.
7. Remove the screws and washer from the rocker arm bosses.
8. Bleed the hydraulic lifters down by applying steady pressure to the pushrod end of the
rocker arm; lifter pressure relief should be obvious.
9. Remove the rocker shafts, rocker arms and thrust washers from the rocker arm
bosses.
10. Withdraw all of the push rods from their respective housings. Mark the location and
position of removal to ensure installation in the same position and location.
11. Compress each push rod housing spring with a Pushrod Spring Compressor Tool.
While the spring is compressed, push the outboard end of the pushrod housing away
from the cylinder head; lower the outboard end of the pushrod housing down and
away from the cylinder. Remove the push rod housing, springs, washers and packing.
12. Discard the packing.
13. Remove the hydraulic lifters from the crankcase lifter bores. Identify the location and
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Cirrus Design SR20西锐20飞行员操作手册和飞机飞行手册附录(118)
