曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
Repair or replace the strike
finder display.
AIRCRAFT
Navigation
DA 40 Series
AMM
Page 102
20 Sep 2007 34-42-00 Doc # 6.02.01
Rev. 5
Intentionally left blank
AIRCRAFT
DA 40 Series
AMM
Navigation
Doc # 6.02.01
Rev. 5 34-42-00 Page 201
20 Sep 2007
Maintenance Practices
1. General
This Section tells you how to remove/install the components of the strike finder system. It also tells you
how to test the strike finder system.
2. Remove/Install the Strike Finder Display
A. Remove the Strike Finder Display
Detail Steps/Work Items Key Items/References
(1) Remove the instrument panel cover. Refer to Section 25-10.
(2) Open the STRIKE circuit-breaker.
(3) Disconnect the connector from the rear of the
strike finder display.
(4) Remove the screws which attach the strike finder
display to the panel.
Hold the instrument!
(5) Remove the strike finder display from the panel.
B. Install the Strike Finder Display
Detail Steps/Work Items Key Items/References
(1) Put the strike finder display in position in the
panel.
(2) Install the screws which attach the strike finder
display to the panel.
(3) Connect the connector to the rear of the strike
finder display.
(4) Install the instrument panel cover. Refer to Section 25-10.
(5) Close the STRIKE circuit-breaker.
(6) Do a test of the strike finder system. Refer to Paragraph 4.
AIRCRAFT
Navigation
DA 40 Series
AMM
Page 202
20 Sep 2007 34-42-00 Doc # 6.02.01
Rev. 5
3. Remove/Install the Strike Finder Sensor
A. Remove the Strike Finder Sensor
Detail Steps/Work Items Key Items/References
(1) Remove the trim/cover from the front face of the
baggage compartment frame.
Pull the rear seat-backs forward.
(2) Open the STRIKE circuit breaker.
(3) Disconnect the connector of the strike finder
sensor.
(4) Remove the screws which attach the strike finder
sensor to the fuselage.
Hold the sensor!
(5) Remove the strike finder sensor from the
fuselage.
B. Install the Strike Finder Sensor
Detail Steps/Work Items Key Items/References
(1) Put the strike finder sensor in position on the
fuselage.
(2) Install the screws which attach the strike finder
sensor to the fuselage.
(3) Connect the connector of the strike finder sensor.
(4) Close the STRIKE circuit breaker.
(5) Install the trim/cover to the front face of the
baggage compartment frame.
(6) Do a test of the strike finder system. Refer to Paragraph 4.
AIRCRAFT
DA 40 Series
AMM
Navigation
Doc # 6.02.01
Rev. 5 34-42-00 Page 203
20 Sep 2007
4. Test the Strike Finder System
Detail Steps/Work Items Key Items/References
(1) Switch the Strike Finder ON:
S Set the ALT/BAT switch ON.
S Set the AVIONIC MASTER switch ON.
(2) Observe three sunburst display test sequences. All display pixels must be visible.
(3) The software revision number must appear in the
lower left corner for a few seconds.
(4) The test status indicator or 'walking dot' must
appear at this time.
(5) Switch the strike finder OFF:
S Set the AVIONIC MASTER switch OFF.
S Set the ALT/BAT switch OFF.
AIRCRAFT
Navigation
DA 40 Series
AMM
Page 204
20 Sep 2007 34-42-00 Doc # 6.02.01
Rev. 5
Intentionally left blank
AIRCRAFT
DA 40 Series
AMM
Navigation
Doc # 6.02.01
Rev. 5 34-45-00 Page 1
20 Sep 2007
Section 34-45
Stormscope System
1. General
This Section tells you about the Stormscope system that can be installed in the DA 40. Refer to the
manufacturer´s manual for more data about the equipment.
The Stormscope system consists of the following items:
) Stormscope processor.
) Stormscope antenna.
% ) DC-AC Inverter
2. Description and Operation
The WX-500 is a passive sensor that listens for electromagnetic signals with a receiving antenna. The
antenna detects intra-cloud, inter-cloud, or cloud-to-ground electrical discharges within a 200 nm
radius of the airplane and sends the resulting 'discharge signals' to the processor. The processor
digitizes, analyzes, and converts the discharge signals into range and bearing data. This information
is stored in the storm buffer.
A. Stormscope Processor
The stormscope processor is tray mounted and is located under the passengers' seat.
% The avionics bus supplies power to the Stormscope system. The ALT/BAT (Lycoming version)
% switch, the ELECTRIC MASTER key switch (TAE version) and the AVIONIC MASTER switch must
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
钻石40系列AMM 2(84)
