曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
S Move the cover plate down and clear of the
control assembly.
(4) Loosen the throttle friction adjuster until the knob
releases from the threaded shaft.
(5) Lift the engine control assembly clear of the
center console and support it.
Hold the friction adjuster knob clear.
Make sure that you do not pull on the
control cables.
AIRCRAFT
Indicating Systems DA 40 Series
AMM
Detail Steps/Work Items Key Items/References
Page 202
20 Sep 2007 31-10-00 Doc # 6.02.01
Rev. 5
(6) Disconnect the following control cables from the
engine control assembly:
S Throttle control cable.
S Propeller control cable.
S Mixture control cable.
S Cabin heat control cable.
S Cabin heat distribution control cable.
S Parking brake control cable.
Refer to Section 76-00.
Refer to Section 61-20.
Refer to Section 76-00.
Refer to Section 21-00.
Refer to Section 21-00.
Refer to Section 32-40.
(7) Move the engine control assembly clear of the
airplane.
B. Install the Engine Control Assembly
Detail Steps/Work Items Key Items/References
(1) Make sure that there are no loose items,
specially in the center console.
(2) Move the engine control assembly onto the
center console and support it in a position where
you can install the control cables.
(3) Connect these control cables to the engine
control assembly:
S Propeller control cable.
S Throttle control cable.
S Mixture control cable.
S Parking brake control cable.
S Cabin heat distribution control cable.
S Cabin heat control cable.
Refer to Section 61-20.
Refer to Section 76-00.
Refer to Section 76-00.
Refer to Section 32-40.
Refer to Section 21-00.
Refer to Section 21-00.
AIRCRAFT
DA 40 Series
AMM
Indicating Systems
Detail Steps/Work Items Key Items/References
Doc # 6.02.01
Rev. 5 31-10-00 Page 203
20 Sep 2007
(4) Pull the throttle friction control knob clear and
lower the engine control assembly into the center
console.
(5) Align the throttle friction control knob to screw
onto the friction shaft in the engine control
assembly.
Do not tighten.
(6) Install the engine control assembly front cover
plate:
S Move the cover plate into position on the
engine control assembly.
S Install the 2 hex-headed bolts which attach
the cover plate and engine control assembly.
Do not tighten.
(7) Install the engine control assembly rear cover
plate:
S Move the cover plate into position on the
engine control assembly.
S Install the 4 cross-head screws which attach
the rear cover plate to the control assembly.
S Tighten the screws.
(8) Tighten the 2 hex-headed bolts in the front cover
plate.
(9) Adjust the throttle friction adjuster to the required
friction.
(10) Do a test for correct range, full and free
movement of the throttle control system.
Refer to the Throttle Control Range of
Movement Test in Section 76-00.
(11) Do a test for correct range, full and free
movement of the mixture control system.
Refer to the Throttle Control Range of
Movement Test in Section 76-00.
(12) Do a test for correct range, full and free
movement of the propeller control system.
Refer to the Throttle Control Range of
Movement Test in Section 61-00.
(13) Do an inspection of the control connections which
you disconnected. If necessary, for your
airworthiness authority, do a second inspection of
the controls.
AIRCRAFT
Indicating Systems DA 40 Series
AMM
Detail Steps/Work Items Key Items/References
Page 204
20 Sep 2007 31-10-00 Doc # 6.02.01
Rev. 5
(14) Do a test for correct range, full and free
movement of the cabin heat control system.
Refer to Section 21-00.
(15) Do a test for correct range, full and free
movement of the cabin heat distribution system.
Refer to Section 21-00.
(16) Install the knob on the fuel selector valve:
S Install the mounting plate.
S Push the knob onto the fuel valve selector
shaft.
S Install the cross-head screw which attaches
the knob to the shaft.
AIRCRAFT
DA 40 Series
AMM
Indicating Systems
Doc # 6.02.01
Rev. 5 31-11-00 Page 1
20 Sep 2007
Section 31-11
Instrument and Control Panels - TAE 125 Diesel Engine
1. General
The DA 40 with the TAE 125 Diesel engine installed has these instrument and control panels:
) An instrument panel. The instrument panel is made in one piece with a shelf. The shelf goes
between the panel and the firewall.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
钻石40系列AMM 2(42)
