32-42-06
ALL ú ú 01 Page 401 ú Sep 28/01
A
757
MAINTENANCE MANUAL
1. HUBCAP ASSEMBLY (PLASTIC) 1
FWD
AXLE NUT SEE A
(REF)
3. BOLT
(2 LOCATIONS)
4. TRANSDUCER
ASSEMBLY
2. SUPPORT
SEE B
1. HUBCAP
ASSEMBLY
(METAL) 1
WHEEL AXLE
(REF)
WHEEL
(REF)
5. NUT
7. RETAINER
NUT 6. WASHER
8. HUBCAP (3 LOCATIONS) BOLT INSTALLATION A 1 PLASTIC OR METAL HUBCAP ASSEMBLY AIRPLANE CAN USE EITHER
Figure 401 (Sheet 1) Antiskid Transducer Installation
32-42-06
ALL ú ú 01 Page 402 ú Dec 20/94
A
757 MAINTENANCE MANUAL
12. TRANSDUCER
7. RETAINER NUT
10. CONE 11. DOG WASHER
9. BOLT
NUT (REF) AXLE
(REF) PLUG CONNECTOR
2. SUPPORT
3. BOLT 6. WASHER B 5. NUT WHEEL (REF)
Figure 401 (Sheet 2) Antiskid Transducer Installation
32-42-06
ALL ú ú 01 Page 403 ú Sep 20/90
A
757 MAINTENANCE MANUAL
S 494-027
WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(2)
Open the doors for the landing gear and install the door locks (AMM 32-00-15/201).
S 864-003
(3)
Open these circuit breakers on overhead circuit breaker panel P11 and attach DO-NOT-CLOSE tags:
(a)
11C31, ANTI-SKID 2-6
(b)
11C32, ANTI-SKID 3-7
(c)
11S18, ANTI-SKID 1-5
(d)
11S22, ANTI-SKID 4-8
E.
Procedure
S 024-004
(1)
Remove three bolts (8) and remove the hubcap assembly (1).
S 024-005
(2)
Remove two axle nut bolts (3) but do not move the axle nut.
S 024-006
CAUTION: DO NOT TWIST THE WIRING HARNESS WHEN YOU REMOVE THE
_______ TRANSDUCER. IF THE WIRING HARNESS IS TWISTED, EQUIPMENT DAMAGE CAN OCCUR.
(3) Pull the assembly of the support (2) and the transducer assembly (4) out from the axle and disconnect the electrical connector.
NOTE: If you use the adapter, B32035-6 it will simplify
____
removal of the support.
S 024-007
(4) Remove the retainer nut (7).
NOTE: Use of retainer nut adapter, B32035-8 will simplify
____
removal of the nut.
S 024-008
(5)
Remove the transducer assembly (4).
S 024-009
(6)
Remove the cone washers (10) and the dog (11) from the transducer assembly (4).
32-42-06
ALL ú ú 01 Page 404 ú Sep 28/01
A
757 MAINTENANCE MANUAL
TASK 32-42-06-404-010
3. Install the Antiskid Transducer (Fig. 401)
_______________________________
A. Equipment
(1) Antiskid Transducer Retainer Nut
Removal/Installation Tool - B32035-10
NOTE: This tool consists of two adapters.
____ The -6 adapter assembly removes/installs the transducer support. The -8 adapter assembly removes/installs the retainer nut.
(2) Adapter-Antiskid Transducer Spin-Up
-A32075-1 (Optional),
-A32075-9 (Optional),
-A32075-10 (Preferred)
(3)
Drill - capable of 500 to 1000 RPM to be used with transducer spin-up adapter. Recommended drill: Chicago Pneumatic Part No. CP-9289-9.
B.
Parts
~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Hubcap Assembly | 32-42-01 | 01 | 80 | | | 2 | Support | 32-42-06 | 01 | 150 | | | 3 | Bolt | 32-42-06 | 01 | 10 | | | 4 | Transducer Assembly | 32-42-06 | 01 | 120 | | | 5 | Nut | 32-42-06 | 01 | 20 | | | 6 | Washer | 32-42-06 | 01 | 15 | | | 7 | Retainer Nut | 32-42-06 | 01 | 135 | | | 8 | Bolt | 32-42-06 | 01 | 5 | | | 9 | Bolt | 32-42-06 | 01 | 125 | | | 10 | Cone Washer | 32-42-06 | 01 | 130 | | | 11 | Dog | 32-42-06 | 01 | 140 | | | 12 | Transducer | 32-42-06 | 01 | 145 | 2.......….......…...................................…...........….....…........1
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 起落架 CHAPTER 32 - LANDING GEAR 3(38)
