32-61-03
ALL ú ú 01 Page 216 ú May 20/98
A
757 MAINTENANCE MANUAL
S 742-051
(2) Use the table that follows to make sure the TARGET NEAR or FAR condition is correct:
~..................................................... | | TARGET LAMP | | SENSOR ..................................... | | NEAR FAR | ....................................................... | S10065 | X | | ....................................................... | S10066 | X | | ....................................................... | S10077 | | X | ....................................................... | S10078 | X | | ....................................................... | S10079 | X | | ....................................................... | S10238 | | X | ....................................................... | S10243 | | X | ....................................................... | S10081 | | X | 2.................….................….................1
S 742-052
(3)
Put the last three numbers of the sensor number on the SENSOR CHANNEL SELECT.
S 742-053
(4)
Push the TARGET TEST button and make sure the correct target indication shows on the BITE control panel.
NOTE: If the TARGET NEAR or TARGET FAR lamps do not come on, do a
____ check of the TARGET lamp that shows the target condition that is not correct.
E. Put the Airplane Back to Its Initial Condition
S 092-054
WARNING:_______OBEY THE REMOVAL PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Remove the door locks from the landing gear doors and close the doors (AMM 32-00-15/201).
32-61-03
ALL ú ú 01 Page 217 ú Sep 28/01
A
757 MAINTENANCE MANUAL
S 862-055
(2) Remove electrical power if it is not necessary (AMM 24-22-00/201).
TASK 32-61-03-422-069
6. Install the Target for the Nose Landing Gear Door Sensor________________________________________________________
A. General
(1)
The target installation task does not have a corresponding removal task. The target installation procedure is to repair a target that has broken free from the nose gear door.
(2)
This procedure requires using an adhesive to bond the target to the nose door panel. Temperature control of the work area is better as this produces a faster curing time for the adhesive (see table 1, figure 205).
B.
References
(1)
AMM 32-00-15/201, Door Locks
C.
Equipment
(1)
Clamp, spring loaded (commercially availiable)
(2)
Heat Lamp, 300 watts (commercially available)
D.
Consumable Materials
(1)
A00870 Adhesive, BMS 5-105 type II class 2
(2)
A00283 Adhesive, BMS 5-92 type II class 2 (optional).
(3)
B00786 Cleaner-Alcohol, Denatured Ethyl
E.
Parts
~.............................................................................. | AMM | | AIPC | .................. ........................... | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 202 | 5 | Target | 32-61-03 | 01 | 295 | | | 5 | Target | 32-61-03 | 01 | 290 | 2.......…........…...................................…..........…......….......1
F. Access
(1)
Location Zones
115 NLG Wheel Well, Left
116 NLG Wheel Well, Right
710 Nose Landing Gear and Doors
G.
Prepare for the target installation which bonds the target to the nose door assembly.
S 862-078
(1)
Disarm the open doors by installing the door locks
(AMM 32-00-15/201).
S 162-070
(2)
Clean both surfaces and then wipe clean with solvent.
32-61-03
ALL ú ú 01 Page 218 ú Jan 28/02
A
757 MAINTENANCE MANUAL
(3) S 342-071Prepare the adhesive (Fig. 205).
NOTE:____ You can choose the fast setup BMS 5-105 which will setup in as little as 2 hours with heat lamps, or rgw BMS 5-92 which will set in about 24 hours depending on ambient temperature. See Fig. 205 for a temperature to time table for BMS 5-105.
(4) S 342-072Bond the target to the door (Fig. 202).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 起落架 CHAPTER 32 - LANDING GEAR 3(170)
